Advertisement
24" Front Load Washer⎯Technical Information
MAH2400A*
• Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or
repair of this unit.
• Refer to Service Manual 16023430 for detailed installation, operating, testing, troubleshooting, and disassembly
instructions.
All safety information must be followed as provided in Service Manual 16023430.
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
June 2006
©2006 Maytag Services
!
CAUTION
!
WARNING
1
16027174
RPL 16023431
Advertisement
Table of Contents
Related Manuals for Maytag MAH2400AW
Summary of Contents for Maytag MAH2400AW
- Page 1 All safety information must be followed as provided in Service Manual 16023430. WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 16027174 RPL 16023431 ©2006 Maytag Services...
- Page 2 • Check motor windings resistance. (Pins 8 & 9 = and no detergent. 3.6 ohms, pins 1 & 10 = 1.1 ohms, Pins 5 & 10 = 1.1 ohms) 16027174 June 2006 RPL 16023431 ©2006 Maytag Services...
-
Page 3: Troubleshooting Procedures
• When display shows "End", only the Power Off Wrong Water Temperature button will function. Press Power Off and make • Check that both faucets are turned on fully. new cycle selections. June 2006 16027174 RPL 16023431 ©2006 Maytag Services... - Page 4 Temperature Temperature Press Power Off (exits Service Mode) Hold Quick Press Start Press Delay Pause (during Start and Spin Step test) Temperature (holds predefined (cancels hold & RPM) resumes next step) 16027174 June 2006 RPL 16023431 ©2006 Maytag Services...
- Page 5 Quick Spin test. To cancel the Hold Rinse Rinse System Check and allow the Spin Test to continue, press the Press Chime – Press Chime Delay Start and Temperature keys. code again displays Diagnostic Code Display (Initial) June 2006 16027174 RPL 16023431 ©2006 Maytag Services...
- Page 6 8. Display a “PA” (Passed) continuously for 5 seconds if no diagnostic codes were logged during the test. Washer will return to the normal Service Mode at the end of the 10 second period. 16027174 June 2006 RPL 16023431 ©2006 Maytag Services...
- Page 7 If the user changes direction and turns the knob in the opposite direction, the more recent code will be displayed. If rotation is continued to the limits of the June 2006 16027174 RPL 16023431 ©2006 Maytag Services...
- Page 8 Not Used board. Input signal from water level Sensor is out of Displays "LE" Water level range, Go to “No Water sensor fault. Washer will Fill”. beep and pause the wash cycle. 16027174 June 2006 RPL 16023431 ©2006 Maytag Services...
- Page 9 Start/Pause key while running a test will pause the Replace motor motor expected. individual test, while remaining in Service Mode. A control board. running. (Abnormal power loss during Service Mode will cancel this mode. condition only). 26-28 Not Used June 2006 16027174 RPL 16023431 ©2006 Maytag Services...
-
Page 10: Drain Pump
Pin 1 on Main. Approx 11,000 or 120 volts. Cold Valve ) Blue wire Pin 2 on CN3 to White wi re Pin 1 on Main. Approx 11,000 ohms or 120 volts. 16027174 June 2006 RPL 16023431 ©2006 Maytag Services... -
Page 11: Component Testing Procedures
Fill Total Spin Total Heavy Duty H/C(N) C/C(N) Normal H/C(N) C/C(N) Wrinkle Control H/C(N) C/C(N) Colors H/C(N) C/C(N) Delicate C/C(N) Handwash C/C(N) Quick Wash H/C(N) Drain Spin C/C(N) Rinse & Spin H/C(N) June 2006 16027174 RPL 16023431 ©2006 Maytag Services... -
Page 12: Wiring Diagram
Wiring Diagram WARNING To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power. CN8 CN6 CN7 CN5 16027174 June 2006 RPL 16023431 ©2006 Maytag Services...
Need help?
Do you have a question about the MAH2400AW and is the answer not in the manual?
Questions and answers