Advertisement
Available languages
Available languages
IMPORTANT:
Read
all instructions
before
operating.
PD Models:
Insert access
door
key, turn,
and
lift to remove
access
doon
PR Models:
Once
the debit card
reader
is installed
(according
to the reader
manufacturing
instructions),
the setup
mode
can be entered
by inserting
a manual
setup
card (supplied
by
the reader
manufacturer)
into the card
slot. If a manual
setup
card
is not available,
manual
setup
mode
can be entered
by removing
connector
AA] on the circuit
board.
Electrical
Shock
Hazard
Disconnect
power
before
servicing.
Replace
all parts
and panels
before
operating.
Failure
to do so can result
in death or electrical
shock.
IMPORTANT:
Unplug
washer
or disconnect
power
before
opening
the console.
To access
connector
AA1, disconnect
poweb
open
console,
disconnect
plug on AA1,
close
console.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
The display
can contain
4 numbers
and/or
letters and a decimal
point. These are used to
indicate
the setup codes and related code values available
for use in programming
the
appliance.
HOW
TO USE THE KEYPADS
TO PROGRAM
THE CONTROLS
1.
The PERMANENT
PRESS keypad
is used to adjust the values associated
with setup codes.
Pressing the keypad
will change the value by increments.
Rapid adjustment
is possible
by
holding
the keypad
down.
2.
The WOOI_ENS
keypad
will
advance
you through
the setup codes.
Pressing the keypad
will
advance
you to the next available
setup code. Holding
the keypad
down will
automatically
advance
through
the setup codes at a rate of 1 per second.
3.
The DEI.ICATES & KNITS keypad
is used to select or dese[ect
options.
Before proceeding,
it is worth
noting that, despite
all of the options
available,
an owner can
simply
choose
to un-crate
a new commercial
washer,
hook it up, plug it in, and have a unit
which
operates.
Units are preset at the factory
for a 14-minute
wash period
and 3 rinses (no extra rinse).
SETUP CODES
The WOOI_ENS
keypad
will advance
you from code to code. The PERMANENT
PRESS
keypad
will change the code value. The DEI.ICATES & KNITS keypad
will select or dese[ect
options.
FOR PR MODEl_S: The setup codes are the same as for the "PD" mode[ except where noted.
The setup code is indicated
by the one or two left-hand
characters.
The setup code value is
indicated
by the two or three right-hand
characters.
CODE EXPLANATION
607
6
REGULAR
CYCLE PRICE
07
Represents the number
of quarters (coin
1 ); may adjust from 0-39. (See VAI.UE
OF COIN
1 .) Advance
from 0-39 by pressing
PERMANENT
PRESS.
Currently
set for 7 quarters
= $1.75.
PR MODEl.
ONI.Y: Currently
set for 0 quarters.
PS MODE
ONI.Y: Represents the number of push-in
actuations
of the coin slide
to start the washer.
601 setting would
represent
one coin slide actuation.
Press WOOI.ENS
keypad
once to advance
to next code.
714
7
WASH LENGTH
14
This is the number
of minutes
for WASH.
Unit comes from the factory
preset
with
14 minutes.
Choose from 9-17 minutes
by pressing
the PERMANENT
PRESS keypad.
Press WOOI.ENS
keypad
once to advance
to next code.
iiiiiiiiiiir_
Plug in washer
or reconnect
power.
The washer
is now in the setup mode.
The lower fabric
setting keypads
and the digital
display
are used to set up the controls.
Advertisement
