Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
Page 2
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH WELL/BLOOMFIELD PRODUCTS. This warranty is void if it is determined that upon inspection by an authorized Wells/Bloomfield service provider that the equipment has been modified, misused, misapplied, improperly installed, or damaged in transit or by fire, flood or act of nature. All problems due to water supply, lime build-up, or high or low water pressure are not covered by this warranty.
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
Page 5
FEATURES & OPERATING CONTROLS (continued) ITEM DESCRIPTION FUNCTION OPTIONAL PREP TOP Allows top of oven to be used as a work surface OVEN TOP Covers and protects top insulation OVEN DOOR Covers and provides access to oven cavity Ergonomic handle is part of the door LATCH Holds oven door closed ACCESS PANEL...
Call your Authorized Wells Service Agent for service. followed. Damage to the appliance will result if The technical content of this manual, including any wiring diagrams,...
INSTALLATION UNPACKING & INSPECTION NOTE: DO NOT discard the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
INSTALLATION (continued) EQUIPMENT SET-UP WARNING: ELECTRIC 1. CURB or COUNTER MOUNTING SHOCK HAZARD a. Setup the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, All servicing requiring terrazzo or metal surfaces are recommended. Metal over access to non-insulated combustible material may not meet code for non-combustible electrical components must...
Page 9
INSTALLATION (continued) DANGER: ELECTRICAL SHOCK HAZARD ELECTRICAL CONNECTIONS MUST BE MADE BY A LICENSED ELECTRICIAN Electrical shock will cause death or serious injury. Refer to the nameplate on the front of the appliance. CAUTION: • Verify the ELECTRICAL SERVICE POWER. RISK OF •...
OPERATION SET TEMPERATURE CAUTION: HOT SURFACE 1. Make sure the power cord is plugged into the appropriate power supply receptacle. Exposed surfaces can be hot 2. Place the ON/OFF/FAN switch in the ON position. to the touch and may cause NOTE: No display will be present until the TEMP key is pressed.
Page 11
OPERATION (continued) CAUTION: DAILY SET-UP PROCEDURES HOT SURFACE 1. Recommended shelf positions for quality baked products: NO. OF PANS RACK POSITION Exposed surfaces can be hot OF PRODUCT UTILIZED to the touch and may cause burns. 2 & 8 2, 5 & 8 2.
CLEANING INSTRUCTIONS CAUTION: PREPARATION Allow oven to cool to 65ºC or less ELECTRIC SHOCK FREQUENCY Daily HAZARD TOOLS Disconnect appliance from Fiber Brush, electric power Mild Detergent, McD Sanitizer, before cleaning. Clean Towel CAUTION: CLEANING BURN HAZARD 1. Turn POWER SWITCH to FAN. With the door held open, allow the Allow appliance to cool oven to cool.
Page 13
CLEANING INSTRUCTIONS (continued) CAUTION: PREPARATION Allow oven to cool to 65ºC or less ELECTRIC SHOCK FREQUENCY Weekly HAZARD TOOLS Fiber Brush, Plastic Scouring Pad, Plastic Scraper Disconnect appliance from electric power Mild Detergent, McD Sanitizer, before cleaning. APC All Purpose Cleaner, Clean Towel CLEANING CAUTION: BURN HAZARD...
PREVENTATIVE MAINTENANCE CAUTION: HINGE ADJUSTMENT Burn Hazard PRECAUTIONS: None Allow appliance FREQUENCY: Monthly, at a Minimum; or, As Needed to cool completely before adjusting. TOOLS: Phillips (+) Screwdriver 7/16" Nut Driver 7/8" and 1-1/8" Wrenches THE FOLLOWING PROCEDURE IS TO BE PERFORMED BY QUALIFIED PERSONNEL ONLY 1.
Hi-limit control tripped on excessive Allow oven to cool oven temperature Hi-limit will reset Damaged controller Contact Authorized Wells Service Agency for repairs Blower fan will not run Fan switch OFF Turn fan switch to HIGH or Damage to internal components...
Page 17
EXPLODED VIEW and PARTS LIST (continued) item description svc p/n ASSY, CAVITY BRACKET, CAVITY SUPPORT GROMMET, 7/8" O.D. 51040 INSULATION, CAVITY (7 parts) INSULATION, MOTOR MOUNT ASSY, BAFFLE SUPPORT MOUNT, TEMP SENSORS COVER, DOOR GASKET CLIP, RACK SUPPORT 63889 HANDLE, DOOR DOOR ASSEMBLY, RETRO KIT, COMPLETE 22914...