Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
Page 2
Seller’s obligation under this warranty is limited to the one year from the date of original installation or 18 months repair of defects without charge by a Wells Mfg. Co. factory from the date of shipment from our factory, whichever...
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
Page 5
FEATURES & OPERATING CONTROLS (continued) ITEM DESCRIPTION FUNCTION A. OPTIONAL PREP TOP Allows top of oven to be used as a work surface B. OVEN TOP Covers and protects top insulation C. OVEN DOOR Covers and provides access to oven cavity D1.
Call your Authorized Wells Service Agent for service. followed. Damage to the The technical content of this manual, including any wiring diagrams,...
Page 7
INSTALLATION UNPACKING & INSPECTION NOTE: DO NOT discard the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
INSTALLATION (continued) WARNING: EQUIPMENT SET-UP Electric 1. CURB or COUNTER MOUNTING Shock hazard a. Setup the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, All servicing requiring terrazzo or metal surfaces are recommended. Metal over access to non-insulated combustible material may not meet code for non-combustible electrical components...
Page 9
INSTALLATION (continued) DANGER: ELECTRICAL SHOCK HAZARD ELECTRICAL CONNECTIONS MUST BE MADE BY A LICENSED ELECTRICIAN Electrical shock will cause death or serious injury. CAUTION: Refer to the nameplate on the front of the appliance. • Verify the ELECTRICAL SERVICE POWER. Risk of •...
OPERATION SET TEMPERATURE CAUTION: Hot Surface 1. Make sure the power cord is plugged into the appropriate power supply receptacle. Exposed surfaces can be hot 2. Place the ON/OFF/FAN switch in the ON position. to the touch and may cause NOTE: No display will be present until the TEMP key is pressed.
Page 11
OPERATION (continued) CAUTION: DAILY SET-UP PROCEDURES Hot Surface 1. Make sure the power cord is plugged into the appropriate power supply receptacle. Exposed surfaces can be hot 2. Recommended shelf positions for quality baked products: to the touch and may cause NO.
CLEANING INSTRUCTIONS CAUTION: PREPARATION Allow oven to cool to 150ºF or less Electric Shock FREQUENCY Daily Hazard TOOLS Fiber Brush, Disconnect appliance from Mild Detergent, McD Sanitizer, electric power Clean Towel before cleaning. CLEANING CAUTION: Burn Hazard 1. Turn POWER SWITCH to FAN. With the door held open, allow the oven to cool.
Page 13
CLEANING INSTRUCTIONS (continued) CAUTION: PREPARATION Allow oven to cool to 150ºF or less Electric Shock FREQUENCY Weekly Hazard TOOLS Fiber Brush, Plastic Scouring Pad, Plastic Scraper Disconnect appliance from Mild Detergent, McD Sanitizer, electric power APC All Purpose Cleaner, Clean Towel before cleaning.
PREVENTATIVE MAINTENANCE CAUTION: HINGE ADJUSTMENT Burn Hazard PRECAUTIONS: None Allow appliance FREQUENCY: Monthly, at a Minimum; or, As Needed to cool completely before adjusting. TOOLS: Phillips (+) Screwdriver 7/16" Nut Driver 7/8" and 1-1/8" Wrenches THE FOLLOWING PROCEDURE IS TO BE PERFORMED BY QUALIFIED PERSONNEL ONLY 1.
Hi-limit control tripped on excessive Allow oven to cool oven temperature Hi-limit will reset Damaged controller Contact Authorized Wells Service Agency for repairs Fan switch OFF Turn fan switch to HIGH or Blower fan will not run Damage to internal components...
Page 17
EXPLODED VIEW and PARTS LIST (continued) M4200-3S Cabinet & Related Components item description svc p/n ASSY, CAVITY PANEL, CONTROL DD-49763 BRACKET, MOTOR MOUNT BRACKET, CAVITY SUPPORT GROMMET, 7/8" O.D. 2K-31040 INSULATION, TOP & BOTTOM INSULATION, WRAP ASSY, BAFFLE SUPPORT MOUNT, TEMP SENSORS COVER, DOOR GASKET CLIP, RACK SUPPORT F6-43889...
Page 18
01/24/11 BBE EXPLODED VIEW and PARTS LIST (continued) Not as Pictured...
Page 19
01/24/11 BBE EXPLODED VIEW and PARTS LIST (continued) M4200-3S Internal Componenets item description svc p/n ASSY, CAVITY TERMINAL BLOCK, 3 POLE WS-50131 SPACER, BLOWER MOTOR LUG, SOLDERLESS FAN, COOLING 2U-44687 PANEL, CONTROL DD-49763 MOTOR, 1/4 HP WS-63932 START CAPACITOR WS-69823 BRACKET, START CAPACITOR 2V-300933 SPACER, MOTOR MOUNT...
OVEN RACK, REPLACEMENT (ea.) 21376 PREP TOP 21445 authorized replacement WALL SPACER KIT 21717 parts, contact your Wells LEG KIT, OVEN, S/S (set of 4) 22226 authorized service agency, or call: Wells Manufacturing Co. 10 Sunnen Dr. St. Louis, MO 63143...
Page 22
PREPARED FOR WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 888-356-5362 fax: 314-781-2714 www.wells-mfg.com...