Korg SGPROX Owner's Manual page 45

Procedure
1) Use the CURSOR switches to select "[" and make it
blink.
2) Use the VALUE switches to move it between 6 and 7.
3) Use the CURSOR switches to select "]" and make it blink.
4) Use the VALUE switches to move it between A and B.
5) Use the CURSOR switches to select "123456" to make it blink.
6) Use the VALUE switches to turn the display to "......"
7) Use the CURSOR switches to make Type blink.
8) Use the VALUE switches to select "SPLIT."
9) Use the CURSOR switches to make "OK?" blink.
10) Press +1/YES to get the "Are You Sure OK?" display.
11) Press +1/YES to execute the setting and get the "Completed" display.
How the velocity range is divided by VEL SW
The locations at which the division will occur will depend on the number of timbres. Lower-numbered
timbres (in the order of 1 to 8, A, B) will be assigned to a lower velocity range.
Example:With a display of "AB[123]45678" if you selected VEL SW, the entire velocity range would be
divided into three ranges, with timbre 1 assigned to the low range (velocity 1 to 42), timbre 2 to the
middle range (velocity 43 to 84), and timbre 3 to the high range (velocity 85 to 127). In this case,
the settings of other timbres will not change.
Procedure
1) Use the CURSOR switches to select "[" and make it
blink.
2) Use the VALUE switches to move it between B and 1.
3) Use the CURSOR switches to select "]" and make it blink.
4) Use the VALUE switches to move it between 3 and 4.
5) Use the CURSOR switches to select "AB 45678" and make sure that they are blinking.
List of macro settings
Settings in ( ) are for timbres A and B — : The setting before macro execution will be maintained Divide : Divide the range by the specified number of timbres.
Timbre No. : Set to the same value as the number of each timbre (Timbre 1 to 8 only)
LAYER
BANK(MSB)
BANK(LSB)
PROGRAM
SW/CHANNEL (ON) –
LEVEL
TRANSPOSE
TUNE
PANPOT
RANDOM PAN
KEY BOTTOM (C–1) C–1
KEY TOP (G9) G9
VEL BOTTOM
VEL TOP 127 (127)
A.WHEEL 1 FILT
A.WHEEL 2 FILT
A.CONT 1 FILT
A.CONT 2 FILT
A.CONT 3 FILT
A.CONT 4 FILT
A.PEDAL FILT
A.PEDAL SW FIL
DAMPER FILT
AFT TOUCH FILT
CONTROLLER FILT
FX1 ROUTING
SPLIT
(–) – (–) –
(–) – (–) –
(–) – (–) –
(ON) –
(–) – (–) –
(–) – (–) –
(–) – (–) –
(–) – (–) –
– –
(Divide) Divide
(Divide) Divide
(1) 1 (1) 1 (Divide) Divide
127 (127) (Divide) Divide
– –
– –
– –
– –
– –
– –
– –
– –
(–) – (–) –
– –
(–) (–)
(–) (–)
Resulting display after steps 1) through 6)
Resulting display after steps 7) through 9)
Resulting display after steps 1) through 5)
VEL SW GM_A
(–) – 056
(A)
(–) – 000
(–) – (1) 000
(ON) – (ON) TimbNo
(–) – 100(100)
(–) – (00) 00
(–) – (00) 00
(–) – (CNT) 64
– ---
(C–1) C–1 (C–1) C–1
(G9) G9 (G9) G9
(1) 1
(127) 127
– ENA
– ENA
– ENA
– ENA
– ENA
– ENA
– ENA
– ENA
(–) – (ENA) ENA
– ENA
(–) (ENA)
(–) (USE)
Performance Edit mode
GM_B RESET
000 000
(A) (A)
000 000
(1) 000 (1) 000
(ON) TimbNo (ON) TimbNo
100(100) (127) 127
(00) 00 (00) 00
(00) 00 (00) 00
(CNT) 64 (CNT) 64
--- ---
(C–1) C–1 (C–1) C–1
(G9) G9 (G9) G9
(1) 1 (1) 1
(127) 127 (127) 127
ENA ENA
ENA ENA
ENA ENA
ENA ENA
ENA ENA
ENA ENA
ENA ENA
ENA ENA
(ENA) ENA (ENA) ENA
ENA ENA
(ENA) (ENA)
(USE) (USE)
45