Category: Special Effect Special Effect - Korg D32XD Owner's Manual

Dry:Wet
Sets the balance between the effect and dry sounds
Waveform (LFO Waveform)
LFO Speed
LFO Step
Env.Resp (Envelope Responce)
Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity)
47: Mono Wah
Control (Control Source)
Wah.Type
Env.Resp (Envelope Responce)
Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity)
Waveform (LFO Waveform)
*LFO Speed
LFO Step
*Manual (Manual Control)
DirectMix (Direct Mix Level)
Wah Level
Category: Special Effect
Special Effect
48: Mn.Analog Record
(Mono Analog Record)
RPM
Wah (Wah Flutter)
Sets the depth by which the record is warped
Bend
Sets the width by which the record is warped
Dry:Wet
Sets the balance between the effect and dry sounds
ClickLevel (Click Noise Level)
ClickAngle (Click Angle)
Sets the angle of the scratch on the surface of the record
LoDamp (Low Damp)
HiDamp (High Damp)
Sets the damping amount in the high range
ClickPoint
Sets the distance of the scratch from the warped area
WhiteLevel (White Noise Level)
164
Dry, 1:99...99:1, Wet
Triangle, Sine, Saw
Selects LFO Waveform
0.02...20.00Hz
Sets the LFO speed
Selects the LFO step
Slow, Medium, Fast
Sets the sensitivity of envelope control
Envelope, LFO, Manual
Switches the control source
Y-CRY, RM-A, RM-B, J-CRY, VOX, M-VOX
Selects the wah type
Slow, Mediumd, Fast
Sets the sensitivity of envelope control
Triangle, Sine, Saw
Selects LFO Waveform
0.02...20.00Hz
Sets the LFO speed
Selects the LFO step
Sets the control position manually
Adjusts the mix level of the direct sound
Sets the wah level
33 1/3, 45, 78
Sets the r.p.m. of a record
Dry, 1:99...99:1, Wet
Sets the level of click noise
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
53Hz...20.0kHz, THRU
Sets the level of white noise
NoiseLoCut (Noise Low Cut)
NoiseHiCut (Noise High Cut)
49: Mn.Ring Modulator
0...256
(Mono Ring Modulator)
Oscilator (Oscilator Frequency)
0...100%
*LFO Speed
Sets the LFO speed of the oscillator frequency modulation
*LFO Depth
Sets the depth of LFO modulation for the oscillator frequency
Dry:Wet
Sets the balance between the effect and dry sounds
Delay (Delay Time)
Feedback
HiDamp (High Damp)
0...100%
In Level (Input Level)
50: Tube Pre Amp Sim
(Tube PreAmp Simulator)
0...256
This effect simulates a vacuum tube preamp. You can make
0...100
independent settings for two vacuum tubes connected in se-
ries, producing a distinctive and warm sound.
0...100%
Tube1.Gain
0...100
Tube1.Sat (Tube1 Satulation)
Tube2.Gain
Tube2.Sat (Tube2 Satulation)
Tb1.LoCut (Tube1 Low Cut)
Sets the amount of low-frequency attenuation for tube circuit 1
Tb1.HiCut (Tube1 High Cut)
Sets the amount of high-frequency attenuation for tube circuit 1
Tb2.LoCut (Tube2 Low Cut)
Sets the amount of low-frequency attenuation for tube circuit 2
Tb2.HiCut (Tube2 High Cut)
Sets the amount of high-frequency attenuation for tube circuit 2
0...100%
Tube1Bias
0...100%
Tb1.Phase (Tube1 Phase)
Tube2Bias
0...100%
Out Level (Output Level)
0...100
0...100
0...100%
THRU, 21Hz...8.00kHz
Sets the low-cut frequency for the noise
53Hz...20.0kHz, THRU
Sets the high-cut frequency for the noise
Sets the oscillator frequency
Dry, 1:99...99:1, Wet
0...2.730sec (1.360sec)
Sets the delay time
Sets the feedback amount
53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Sets the input level to the effect
Sets the gain of tube circuit 1
Sets the amount of saturation for tube circuit 1
Sets the gain of tube circuit 2
Sets the amount of saturation for tube circuit 2
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
Sets the bias for tube circuit 1
Sets the output phase of tube circuit 1
Sets the bias for tube circuit 2
Sets the output level
0...12.00kHz
0.02...20.00Hz
0...100%
–100...+100%
0...100%
–24.0...+24.0dB
0...100%
–24.0...+24.0dB
0...100%
0...100%
Normal, Inverted
0...100%
–48.0...0.0dB