Location; Switching The Counter Display; Switching The Information Display Area; Moving To A Different Location - Korg D32XD Owner's Manual

2. Location

The term "location" refers to a specific point in time within
the selected song, as displayed in the counter.
The counter shows the current location within the song. The
counter can be set to display the location in different formats.
You can also use the counter to move to a different location.

2-1. Switching the counter display

You can switch the units that the counter uses to display the
current location.
(1) Press the button to the left of the counter to open
the Time Disp Type dialog box.
Information display
(2)
(2)
(2) Select the type of units you want the counter to use,
and press the OK button.
You can choose one of the following three formats
( p.96 "Counter").
Time display
• __:__:__.___
"milliseconds"
Frame display
• __:__:__:.__F
"frames"
Measure display
• ___.__.___

Switching the information display area

The first line of the information display area shows the cur-
rently selected song. The second line can be switched to show
either the calendar, remaining time, scene settings, mark set-
tings, or tempo map.
(1) Press the button at the left of the counter to display
the Time Disp Type dialog box.
(2) Press one of the following five radio buttons, and then
press the OK button.
• Date Time: calendar (date and time)
• Free Time: remaining time for recording
• Scene: name and location of the scene for the current
location in the song
• Mark: name of the mark for the current location in the
song. If there is no mark at the current location, this
displays the preceding mark and its location.
• TempoMap: the rhythm pattern at the current location
of the song

2-2. Moving to a different location

Using the counter to move

(1) Select a page in which the counter is displayed at the
top of the screen, such as the SONG, "SelectSong" tab
page.
38
(1)
(2)
"hours" : "minutes" : "seconds" .
"hours" : "minutes" : "seconds" .
"measures" . "beats" . "ticks"
(2) Select the location counter unit that you want to
change (it will be enclosed by a frame).
(3) Turn the value dial (or use the +/– keys) to move to the
new location.

Using the FF and REW keys to move

Moving to a point later in the song (fast-forward)

Press the FF key.
If you hold down the FF key during playback, you will move
toward the end of the song. Playback will resume when you
release the key.
If you hold down the FF key while stopped, you will begin
moving toward the end of the song and will continue moving
until you press another transport key (such as STOP or
PLAY).
If you press the FF key during loop playback, loop playback will
stop, and then the location will begin moving toward the end of the
song.

Moving to a point earlier in the song (rewind)

Press the REW key.
If you hold down the REW key during playback, you will
move toward the beginning of the song. Playback will
resume when you release the key.
If you hold down the REW key while stopped, you will begin
moving toward the beginning of the song and will continue
moving until you press another transport key (such as STOP
or PLAY).
If you press the REW key during loop playback, loop playback will
stop, and then the location will begin moving toward the begin-
ning of the song.

Moving within a song

Moving to the beginning of the song

Hold down the STOP key and press the MARK JUMP (√)
key to move to the beginning of the song.

Moving to the end of the song

Hold down the STOP key and press the MARK JUMP (®)
key to move to the end of the song.

Using the Locate keys to move

You can register a specific location for each of the Locate
keys, and move immediately to those locations by pressing
the appropriate key.
You can register up to six locations in each song.
In addition to recalling the registered locations, these keys are also
used to specify locations for auto-punch recording (IN/OUT loca-
tions) and track editing (editing range). For details on the func-
tion of each locate key, refer to "16. LOC1/IN, ... LOC6"
( p.149).

Assigning locations to the Locate keys

(1) Move to the location that you want to register.
Use the counter or the FF/REW keys to move to the
desired location.
(2) Press the STORE key; the Stored Time dialog box will
appear, allowing you to register the location.
If you decide to cancel, press the Exit button or press the
STORE key once again.
(2)