Korg D32XD Owner's Manual page 165

EQ Trim
LEQ Gain (Pre LEQ Gain)
HEQ Gain (Pre HEQ Gain)
P.DlyThru (Pre Delay Thru)
Sets the mix ratio of non-delay sound
Rev Level (Reverb Level)
ER Level
: ER Level, : Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values allows you to simulate the
type of walls in the room. That is, a larger "ER Level" simulates
a hard wall, and a larger "Reverb Level" simulates a soft wall.
7: Eary Reflection
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of
the four decay curves.
Type Sharp, Loose, Modulated, Reverse
Selects the decay curve for the early reflection
ER Time
Sets the time length of early reflection
Predly (Pre Delay)
Sets the time taken from the original sound to the first early
EQ Trim
LEQ Gain (Pre LEQ Gain)
HEQ Gain (Pre HEQ Gain)
Dry:Wet
Sets the balance between the effect and dry sounds
: Type
This parameter selects the decay curve for the early reflection.
8: L/C/R Delay
This multitap delay outputs three Tap signals to the left,
right, and center respectively. You can also adjust the left and
right spread of the delay sound.
L Time (L Delay Time)
C Time (C Delay Time)
R Time (R Delay Time)
Dry:Wet
Sets the balance between the effect and dry sounds
L LevelL (Delay Level)
C LevelC (Delay Level)
R LevelR (Delay Level)
Spread
Sets the width of the stereo image of the effect sound
Fdback (C) (Feedback (C Delay))
Sets the feedback amount of TapC
–15...+15dB
Sets the equalizer trim level
–15...+15dB
Sets the gain of Low EQ
–15...+15dB
Sets the gain of High EQ
0...100%
0...100%
Sets the reverberation level
0...100%
Sets the level of early reflections
10...800msec
0...200msec
reflection
–15...+15dB
Sets the equalizer trim level
–15...+15dB
Sets the gain of Low EQ
–15...+15dB
Sets the gain of High EQ
Dry, 1:99...99:1, Wet
0...2.730sec (1.360sec)
Sets the delay time of TapL
0...2.730sec (1.360sec)
Sets the delay time of TapC
0...2.730sec (1.360sec)
Sets the delay time of TapR
Dry, 1:99...99:1, Wet
0...100%
Sets the output level of TapL
0...100%
Sets the output level of TapC
0...100%
Sets the output level of TapR
0...100%
–100...+100%
Fb.LoDamp (Feedback Low Damp)
Sets the damping amount in the low range
Fb.HiDamp (Feedback High Damp)
Sets the damping amount in the high range
In Level (Input Level)
: High Damp, : Low Damp
These parameters set the damping amount of high range and
low range. The tone of the delayed sound becomes darker and
lighter as it feeds back.
: Spread
This parameter sets the pan width of the effect sound. The
stereo image is widest with a value of "50," and the effect
sound of both channels is output from the center with a value
of "0."
9: Stereo/Cross Delay
This is a stereo delay, and can by used as a cross-feedback de-
lay effect in which the delay sounds cross over between the
left and right by changing the feedback routing.
L Time (L Delay Time)
R Time (R Delay Time)
Type (Stereo/Cross)
Switches between stereo delay and cross-feedback delay
Dry:Wet
Sets the balance between the effect and dry sounds
L Fdback (L Feedback)
Sets the feedback amount for the left channel
R Fdback (R Feedback)
Sets the feedback amount for the right channel
LoDamp (Low Damp)
Sets the damping amount in the low range
HiDamp (High Damp)
Sets the damping amount in the high range
Spread
Sets the width of the stereo image of the effect sound
In Level (Input Level)
10: St. Multitap Delay
(Stereo Multitap Delay)
The left and right Multitap Delays have two taps respective-
ly. Changing the routing of feedback and tap output allows
you to create various patterns of complex effect sounds.
Tap1Time
Tap2Time
Type Normal, CrossFdback, CrossPan1, CrossPan2
Switches the left and right delay routing
Dry:Wet
Sets the balance between the effect and dry sounds
Tap1Level
Tap2Level
T1.Fdback (Tap1 Feedback)
Spread
Sets the width of the stereo image of the effect sound
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
0...100%
Sets the input level to the effect
0...2.730sec (1.360sec)
Sets the left delay time
0...2.730sec (1.360sec)
Sets the right delay time
Stereo, Cross
Dry, 1:99...99:1, Wet
–100...+100%
–100...+100%
THRU, 21Hz...8.00kHz
53Hz...20.0kHz, THRU
0...100%
0...100%
Sets the input level to the effect
0...2.730sec (1.360sec)
Sets the delay time of Tap1
0...2.730sec (1.360sec)
Sets the delay time of Tap2
Dry, 1:99...99:1, Wet
0...100%
Sets the output level of Tap1
0...100%
Sets the output level of Tap2
–100...+100%
Sets the Tap1 feedback amount
0...100%
155