Category: Dynamics&Filter Dynamics/Filter-Type Effects - Korg D32XD Owner's Manual

Release
L-R Phase (LFO L-R Phase)
Sets the LFO phase difference between the left and right
Waveform (LFO Waveform)
LFO Shape
Determines how much the LFO waveform is changed
18: Stereo Tremolo
This effect modulates the volume level of the input signal.
The effect is stereo, and offsetting the LFO of the left and
right phases from each other produces a tremolo effect be-
tween left and right.
*Speed (LFO Speed)
*Depth
Waveform (LFO Waveform)
Dry:Wet
Sets the balance between the effect and dry sounds
LFO Shape
Determines how much the LFO waveform is changed
L-R Phase (LFO L-R Phase)
Sets the LFO phase difference between the left and right
: LFO Waveform
This parameter selects the LFO waveform.
: LFO Phase
This parameter determines the difference between the left and
right LFO phases. A higher value will simulate the auto-pan
effect in which the sound is panned between left and right.
19: St.Pitch Shifter
(Stereo Pitch Shifter)
This is a stereo pitch shifter.
PitchShift
Sets the pitch shift amount in steps of a semitone
Fine
Sets the pitch shift amount in steps of one cent
Lo/Hi Cut (Low/High Cut)
Sets the damping amount in the low/high range
Dry:Wet
Sets the balance between the effect and dry sounds
Feedback
L Time (L Delay Time)
R Time (R Delay Time)
Fb.Position (Feedback Position)
In Level (Input Level)
Spread
Sets the width of the stereo image of the effect sound
: Feedback Position, : Feedback
If "Feedback Position" is set to Pre (Pitch), the output of the
pitch shifter will be fed back into the input of the pitch shifter;
this means that by raising the "Feedback" value you can create
an effect in which the pitch of the feedback continues to rise (or
fall) each time the feedback delay is repeated.
158
Sets the release time for level control
–180...+180deg
Triangle, Sine
Selects LFO Waveform
–100...+100%
0.02...20.00Hz
Sets the LFO speed
Sets the depth of LFO modulation
Triangle, Sine, Square, Saw up, Saw down
Selects LFO Waveform
Dry, 1:99...99:1, Wet
–100...+100%
–180...+180deg
–24...+24/2tone
–100...+100cent
Lo:–50%..., Flat, ...Hi:–50%
Dry, 1:99...99:1, Wet
–100...+100%
Sets the feedback amount
0...1.360sec (680msec)
Sets the left delay time
0...1.360sec (680msec)
Sets the right delay time
Pre (Pitch), Post (Dly)
Switches the feedback connection
Sets the input level to the effect
If "Feedback Position" is set to Post (Dly), the sound that is fed
0...10.0sec
back will not be sent through the pitch shifter again; this means
that if you raise the "Feedback" value, the pitch-shifted sound
will repeat at that same pitch.
Category: Dynamics&Filter
Dynamics/Filter-type effects
20: Stereo Compressor
This effect compresses the input signal to regulate the level
and give a "punchy" effect. This is a stereo compressor. You
can link left and right channels, or use each channel separate-
ly.
Threshold
0...100
Ratio
Attack
Release
Env.Select (Envelope Select)
Switches the left/right channels between linked or independent
Responce
Tube Sat (Tube Satulation)
Out Gain (Output Gain)
: Envelope Select
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
: Response
Adjusts the response speed at which the envelope is detected.
Select the setting that is appropriate for the input material;
choose Fast for brief sounds like percussion instruments,
Medium for vocals, or Slow for long-sustaining sounds.
21: Stereo Expander
This effect attenuates input signals that are below a specified
level, adding punch to the sound and improving the S/N ra-
tio by reducing the level between performances.
Threshold
Ratio
Attack
Release
0...100%
Env.Select (Envelope Select)
Switches the left/right channels between linked or independent
–100...100%
Responce
Out Gain (Output Gain)
Sets the level at which compression begins to apply
Sets the compression ration of the signal
Selects the response speed
Sets the depth of vacuum tube distortion
Adjusts the output level gain
Sets the level at which compression begins to apply
Sets the compression ration of the signal
Selects the response speed
Adjusts the output level gain
–30.0...0.0dB
1.00:1...20.0:1
0...1.00sec
Sets the attack time
0...10.0sec
Sets the release time
L/R Mix, L/R Indiv
operation
Slow, Medium, Fast
0...100
–24.0...+24.0dB
–48.0...0.0dB
1.00:1...20.0:1
0...1.00sec
Sets the attack time
0...10.0sec
Sets the release time
L/R Mix, L/R Indiv
operation
Slow, Medium, Fast
–24.0...+24.0dB