Barco R9000740 Installation Manual
  1. Manuals
  2. Brands
  3. Barco Manuals
  4. Projector
  5. BarcoVision R9000740
  6. Installation manual
Barco R9000740 Installation Manual

Barco R9000740 Installation Manual

Hide thumbs Also See for R9000740:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
BARCO PROJECTION SYSTEMS
Date:
070597
701 MULTIMEDIA
R9000740
INSTALLATION MANUAL
VISION
Rev. :
01
Art. No.
R5975248

Advertisement

Table of Contents
loading

Related Manuals for Barco R9000740

Summary of Contents for Barco R9000740

  • Page 1 BARCO PROJECTION SYSTEMS VISION 701 MULTIMEDIA R9000740 INSTALLATION MANUAL Rev. : Date: Art. No. 070597 R5975248...
  • Page 2 Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, May 1997. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 8520 Kuurne Belgium...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS WARNINGS ......................1-1 SAFETY INSTRUCTIONS ..................1-1 On safety ...................... 1-4 On installation ....................1-5 On servicing ....................1-6 On cleaning ....................1-6 On repacking ....................1-7 On illumination ....................1-7 UNPACKING & DIMENSIONS ................2-1 Unpacking ..................... 2-2 Projector dimensions ..................
  • Page 4 TABLE OF CONTENTS i-II 5975248 BARCOVISION 701 MULTIMEDIA 070597...

  • Page 5: Warnings

    SAFETY INSTRUCTIONS WARNINGS SAFETY INSTRUCTIONS on safety on installation on servicing on cleaning on repacking on illumination 5975248 BARCOVISION 701 MULTIMEDIA 090497...
  • Page 6 Before operating your projector please read this manual thoroughly, and retain it for future reference. Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers. OWNER’S RECORD The part number and serial number are located at the left side of the projector.
  • Page 7 SAFETY INSTRUCTIONS The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions are in- cluded in the technical documentation for this equipment.

  • Page 8: On Safety

    1. This product should be operated from an AC power source Operating AC power voltage of the projector when leaving the factory: BARCOVISION 701 MULTIMEDIA Art.No. R9000740 (230V AC) The projector leaves the factory for 230 Vac. Consult your dealer to switch over to 120 VAC.

  • Page 9: On Installation

    SAFETY INSTRUCTIONS B. Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code. Green/yellow: ground White: neutral Black: line (live) 3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.

  • Page 10: On Servicing

    Replacement parts - When replacement parts are required, be sure the service technician has used original BARCO replacement parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards.

  • Page 11: On Repacking

    SAFETY INSTRUCTIONS - To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
  • Page 12 SAFETY INSTRUCTIONS 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 13: Unpacking & Dimensions

    UNPACKING AND DIMENSIONS UNPACKING DIMENSIONS 5975248 BARCOVISION 701 MULTIMEDIA 090797...
  • Page 14 UNPACKING AND DIMENSIONS Unpacking To open de banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, they will come in handy if you ever have to ship your projector.

  • Page 15: Projector Dimensions

    UNPACKING AND DIMENSIONS Projector dimensions 5975248 BARCOVISION 701 MULTIMEDIA 090797...

  • Page 16: Unpacking And Dimensions

    UNPACKING AND DIMENSIONS 5975248 BARCOVISION 701 MULTIMEDIA 090797...

  • Page 17: Installation Guidelines

    INSTALLATION GUIDELINES INSTALLATION GUIDELINES Environment What about ambient light? Which screen type? What image size? How big should the image be? Where to install the projector? How to install the projector? 5975248 BARCOVISION 701 MULTIMEDIA 090797...
  • Page 18 INSTALLATION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. * Environment Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity.
  • Page 19 The BARCOVISION 701 MULTIMEDIA is designed for projecting an image width from 1.4m (4.6') to 7m (23') with an aspect ratio of 4 to 3. It leaves the BARCO factory, adjusted as a ceiling front projector for a screen width of 2.4m. Changing the image size from the factory preset requires a realignment of the projector.
  • Page 20 INSTALLATION GUIDELINES * Where to install the projector? To indicate a correct installation position it is necessary to know the distance : - projector - ceiling - projector - screen To find this correct position for the BARCOVISION 701 MULTIMEDIA, equipped with HD145 lenses, formulas are given in the next paragraph.
  • Page 21 INSTALLATION GUIDELINES ceiling projector screen Front view screen width Top view 5975248 BARCOVISION 701 MULTIMEDIA 090797...
  • Page 22 INSTALLATION GUIDELINES * How to install the projector? Ceiling mount or table mount? To install the projector, apply always the BARCO kits which are specially designed for this function. BARCO ceiling support. Always use the BARCO ceiling support to attach your projector to the ceiling. (BARCO order number : R9827990) The installation instruction for this support is enclosed in the packet of the set.

  • Page 23: Installation Set Up

    INSTALLATION SET UP INSTALLATION SET UP Access to controls Scan adaptation 5975248 BARCOVISION 701 MULTIMEDIA 070597...

  • Page 24: Access To Controls

    INSTALLATION SET UP Access to controls Opening procedure : During the projector set up and installation it is necessary to open the top cover. To gain access, procede as follow : *Turn both lock screws with a screwdriver or a coin counter clockwise. * Lift up and pivot the top cover.
  • Page 25 INSTALLATION SET UP During some installations it will become handy to remove the top cover totally. Therefore, - pivote the top cover ± 60° - push the top cover to the front side of the projector until it jumps out of its hings. Turn the top cover till 90°...

  • Page 26: Scan Adaptation

    INSTALLATION SET UP Scan adaptation The scanning can be switch by turning the Horizontal and Vertical scan connectors and the convergence connectors. To change the scanning, it is necessary to open the projector top cover and to rotate the chassis. For opening the projector's top cover, see Getting access to controls.
  • Page 27 INSTALLATION SET UP Horizontal scan connectors Vertical scan connectors Convergence connectors COMM PORT S-VIDEO (800 peripherals) REMOTE G(S) VIDEO RS232 OUT RS232 IN 5975248 BARCOVISION 701 MULTIMEDIA 070597...
  • Page 28 INSTALLATION SET UP A : Horizontal scan inversion Three connectors are used, one for each horizontal deflection coil. When changing the horizontal scan, insure that all three connectors are set in the same position. See position of the connectors for the corresponding projector configuration. B : Vertical scan inversion Three connectors are used, one for each vertical deflection coil.
  • Page 29 INSTALLATION SET UP After scan inversion, close the chassis and close the top cover. Reconnect the power cord to the wall outlet. Note Switching over from floor to ceiling or vice versa requires a complete readjustment of picture geometry and convergence. Check of the correct connector position Note : this check procedure can only be done after power (mains) connection.
  • Page 30 IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE : operating BARCO LOGO Select with then <ENTER> <EXIT> to return. The projector displays the Identifica- tion screen This screen gives information about the projector configuration in the sub- V 701 MULTIMEDIA ject 'config.'.

  • Page 31: Projector Set Up

    PROJECTOR SET UP PROJECTOR SET UP Password mode 5975248 BARCOVISION 701 MULTIMEDIA 070597...
  • Page 32 PROJECTOR SET UP Projector Set Up The strap on the CPU unit allow a set up of the password mode. Gaining access to the strap - Open the top cover (see installation set up) - Open the chassis (see installation set up) strap Horizontal scan connectors...

  • Page 33: Password Mode

    PROJECTOR SET UP Password mode With a strap on the controller unit, the important projector adjustments can be protected with a password. When the password feature is enabled (strap mounted on both legs), the customer has to enter a password before he can enter the specific adjustment.
  • Page 34 PROJECTOR SET UP 5975248 BARCOVISION 701 MULTIMEDIA 070597...

  • Page 35: Power (Mains) Connection

    POWER CONNECTION POWER (MAINS) CONNECTION 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 36: Input Power (Mains) Voltage Adaptation

    Input power (mains) voltage adaptation. Attention The BARCOVISION 701 MULTIMEDIA - R9000740 leaves the factory to operate on a mains (power) input of 230 Vac. Adaptation of the power input of the projector from 230 VAC to 120 VAC or vice versa is possible.

  • Page 37: Power Connection

    POWER CONNECTION See installation instructions before connecting to the supply V NOM 120/230 Volt I MAX 5/2.5 AMP FREQ 60/50 Hz - Push out the module. 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 38: Fuses

    Fuses Warning For continued protection against fire hazard : - replace with the same type of fuse - refer replacement to qualified service personnel Fuse type : 2 x T5A/250V (Barco order number : R314104) 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 39: Switching On/Off

    POWER CONNECTION Switching on/off The projector is switched ON and OFF using the power (mains) switch ON/OFF. Pressed : ON Not pressed : OFF The projector can start now in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit. This DIP switch is set during installation by a qualified technician.
  • Page 40 POWER CONNECTION 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 41: Installation Adjustments

    INSTALLATION ADJUSTMENTS INSTALLATION ADJUSTMENTS Overview flow chart installation mode Scheimpfug adjustment Optical lens focusing Raster centering CRT projection angle adjustment Alignment of the projector 5975248 BARCOVISION 701 MULTIMEDIA 070597...

  • Page 42: Entering The Adjustment Mode

    INSTALLATION ADJUSTMENTS Entering the adjustment mode ADJUSTMENT MODE Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return IRIS Installation (only for qualified technician) Random Access Service Adjustment Guided Adjustment 5975248 BARCOVISION 701 MULTIMEDIA 070597...

  • Page 43: Overview Flow Chart Installation Mode

    INSTALLATION ADJUSTMENTS Overview flow chart installation mode. OPTICAL LENS FOCUSING SCHEIMPFLUG ADJUSTMENT 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, ROTATE THE LENS BARREL LOOSEN THE 4 TO FOCUS THE CENTER LENS MOUNTING NUTS ON OF THE IMAGE, EACH LENS, UNTIL THE TAG THEN TIGHTEN THE NUT OF EACH SCHEIMPFLUG RING...

  • Page 44: Installation Mode Start Up

    INSTALLATION ADJUSTMENTS Installation mode start up It will be necessary to perform several mechanical adjustments while in the installation mode. Remove the top cover in order to gain access to the adjustment points (see Access to controls). Two possible ways to enter the installation mode : a) Using the RCU.
  • Page 45 INSIDE the installation mode. THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR When entering the installation mode, BARCO AUTHORIZED DEALERS the projector will automatically switch IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR to the internal pattern on 15 kHz/50 Hz.
  • Page 46 INSTALLATION ADJUSTMENTS When the password mode is active, your password will be asked. Your password contains 4 digits. a) Adjusting the projector with the RCU. Enter the digits with the numeric keys on the RCU. Example : 2 3 1 9 For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'.
  • Page 47 INSTALLATION ADJUSTMENTS b) adjusting the projector with the local keypad. When the 'compose password' menu is displayed, select with the control COMPOSE disk the first digit of your password PASSWORD and press ENTER. Continue by se- lecting the second digit with the con- 7 8 9 trol disk and press ENTER.

  • Page 48: Scheimpfug Adjustment

    INSTALLATION ADJUSTMENTS Scheimpfug adjustment The scheimpfug correction can be adjusted separately for the three tubes within 3 ranges: range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55") range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94") range 3 : 3.2 m (126") to 6 m (236"), optimum screen width 4 m (157") A correct scheimpfug setting gives the possibility to focus the lenses for a sharp image in all screen areas.
  • Page 49 INSTALLATION ADJUSTMENTS 1. Open the top cover (see Gaining access to controls) 2. Loosen the lens bolts (do not remove them), and slide the lens to the front until the scheimflug ring can move freely (nutdriver 8 mm or screwdriver). Lens bolts Lens bolts Lens bolts...

  • Page 50: Optical Lens Focusing

    INSTALLATION ADJUSTMENTS Optical lens focusing The optical focusing procedure is performed separately for each lens. OPTICAL LENS FOCUSING The appropriate CRT will be switched 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, on as the user proceeds through the ROTATE THE LENS BARREL optical focusing adjustment se- TO FOCUS THE CENTER...

  • Page 51: Electrical Focusing

    INSTALLATION ADJUSTMENTS Electrical focusing The electrical focus for red, green and blue is factory preset. When they have to be readjusted, follow the procedure as described below : - Ensure the lenses are correctly focused. - Open the top cover. - Adjust separately the focus control for red, green and blue for the sharpest image on the screen.

  • Page 52: Raster Centering

    INSTALLATION ADJUSTMENTS Raster centering The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses. Caution : To avoid eye discomfort while performing these adjustments, reduce the contrast and gradually increase the brightness level until the raster becomes visible behind the image.
  • Page 53 INSTALLATION ADJUSTMENTS correct raster position wrong raster position Press ENTER to activate the raster on the Red CRT faceplate. Shift the raster with the control disk until the raster is centered in the mid- dle of the CRT faceplate. Press ENTER to activate the raster on the Blue CRT faceplate.

  • Page 54: Crt Projection Angle Adjustment

    INSTALLATION ADJUSTMENTS CRT projection angle adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Never try to correct this misalignment with the shift correction or the static convergence controls.
  • Page 55 INSTALLATION ADJUSTMENTS Projection angle correctly aligned The same projection angle is mis-aligned for for screen width SW1 new screen width SW2. Re-alignment is neces- sary. Each screen width change requires read- justment of the projection angle. (SW2>SW1) 5975248 BARCOVISION 701 MULTIMEDIA 070597 7-15...
  • Page 56 INSTALLATION ADJUSTMENTS A' A Screws A, B, C and D (M4) : upper fixation latch. nutdriver 7mm. Screw A', B', C' and D' (M4) : lower fixation latch. nutdriver 7mm. Loosen the four hexagon screws A, A', B and B', upper and lower fixation latch.
  • Page 57 INSTALLATION ADJUSTMENTS Loosen the four hexagon screws C, C', Dand D', upper and lower fixation latch. These screws fasten the cooling house PROJECTION ANGLE of the blue tube. ADJUSTMENT Pivot the blue CRT until the center of the blue image coincides with the center of the green image.

  • Page 58: Alignment Of The Projector

    INSTALLATION ADJUSTMENTS Alignment of the projector. Overview of the corrections For detailed information about these corrections and procedures to be followed, see owner's manual. (pages given hereafter are for the random access adjustment mode) Shift corrections for the Red, Green and Blue image. Left-Right adjustments - Vertical center line bow and skew - Left and right keystone adjustment...

  • Page 59: Appendix A : Ceiling Mount Kit For 700 Projectors

    Ceiling mount kit for 700 projectors (CM50). This ceiling mount with or without pulley system enables to mount the BARCO 700 projector to the ceiling. The concept makes it possible to adapt the projector perfectly to the local mounting requirements in a safe and solid manner.
  • Page 60 APPENDIX A : CEILING MOUNT KIT CM50 5975248 BARCOVISION 701 MULTIMEDIA 090497...

  • Page 61: Appendix B : G2 Adjustment

    APPENDIX B : G2 ADJUSTMENT G2 adjustment Enter the adjustment mode by pressing ADJUST and highlight Service. Press ADJUSTMENT MODE ENTER to start up the service mode. Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER>...
  • Page 62 SAFETY NOTICE service menu. RISK OF ELECTRICAL SHOCK G2 ADJUSTMENT SHOULD BE PERFORMED BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS. IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN. If ENTER is pressed, the G2 menu will be displayed.
  • Page 63 APPENDIX B : G2 ADJUSTMENT Switch ABL to OFF by pressing ENTER and adjust the G2 control until the raster brightness looks the same as when the ABL function is ON. Check the correct raster adjustment by pressing ENTER to toggle ABL to ON. Repeat these steps if necessary.
  • Page 64 APPENDIX B : G2 ADJUSTMENT 5975248 BARCOVISION 701 MULTIMEDIA 070597...

Table of Contents