Barco R9000901 Installation Manual
Hide thumbs
Also See for R9000901:
- Owner's manual (55 pages) ,
- Replacement manual (14 pages) ,
- Isntallation manual (41 pages)
Related Manuals for Barco R9000901
Summary of Contents for Barco R9000901
- Page 5 Contents...
- Page 7 • • • • • • • • •...
- Page 8 • • • • • • • • • • • • • •...
- Page 9 • • • • •...
- Page 12 • • • • 11.5 cm green phospho...
- Page 13 • • • • • • •...
- Page 14 • • • • • •...
- Page 15 • • •...
- Page 16 • • ADJUSTMENT MODE • Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return • Select with then <ENTER> <EXIT> to return BS6QCD8TÃ''† Proj. address : 001 Soft. Version : 5.00 Config.
- Page 17 • • • • PASSWORD MODE POWER UP MODE PASSWORD REQUIRED OPERATING MODE WHEN FOR ADJUSTMENT POWER IS SWITCHED ON PLAYING StdBY BAUD RATE TABLE TO COMPUTER PROJECTOR ADDRESS StdBY (sum) CODE SPEED MAIN POWER PROCESSOR CYC I 2 C SHORTED BLOCK MATCH RESERVED ERROR...
- Page 18 • Source 2 Fh= 15.6 kHz Fv= 50 Hz •...
- Page 19 OFF ON OFF ON...
- Page 20 'Ãr…vƒur…hy† &$ÃPu€ &$ à Pu€ $%à C“ PORT 2 POWE R / MAINS COMM. P ORT PORT 3 POR T 4/5 PORT 1 PROJECT OR MODE &$Ã6 €ƒ $%ÃC“ P O W E R / M A IN S • •...
- Page 21 6…‡Ã…‘‘‘‘‘‘‘‘‘ Tr…vhyÅÑ‘‘‘‘‘‘ • • • • • • • •...
- Page 22 • • &$Ã6 €ƒ $%ÃC“ P O W E R / M A IN S • •...
- Page 23 • • ' Ã ƒr …vƒur… hy † • &$ ÃPu € & $ÃP u€ PORT 4/5 PORT 2 P OWER / MAIN S COMM. PO RT P ORT 3 PO RT 1 PROJECT OR MODE • • •...
- Page 24 ' Ã r… v ƒu r… h y† &$ ÃPu€ &$ ÃPu€ $ % à C“ P O RT 4/ 5 PORT 2 POWER / MAINS COMM. POR T PORT 3 POR T 1 PROJ ECTOR MOD E L Q Y H U &$Âu€...
- Page 25 • • • • • • • • &$à ‚u €Ã‡ r …€ LQ YHU ' à ƒr…vƒur…hy† &$ÃPu € &$à Pu€ $ % à C“ POR T 4 /5 P ORT 2 P OW ER / MAINS COMM. P ORT P ORT 3 PORT 1 PROJECT OR MODE...
- Page 26 ' Ã r …v ƒ u r …h y† &$ à P u€ & $ÃP u€ $ % à C “ PO RT 2 POWER / MAIN S COMM. POR T POR T 3 PO R T 4/5 PORT 1 PR OJECTOR MODE ' Ã...
- Page 27 • • WARNING • RISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, • AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS • IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT>...
- Page 28 • • • • • • • 1. LOOSEN THE NUT ON THE REAR OF THE GREEN LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER OF THE IMAGE, THEN TIGHTEN THE NUT 2. LOOSEN THE NUT ON THE FRONT OF THE GREEN LENS AND ROTATE THE FRONT SECTION OF THE LENS TO FOCUS THE CORNERS OF THE...
- Page 29 CONTRAST LEVEL IS REDUCED AND BRIGHTNESS INCREASED TO MAKE THE RASTER VISIBLE ON THE FACE PLATE OF EACH CRT. USE THE ARROW KEYS TO CENTER THE RASTER ON THE GREEN, RED AND BLUE CRT RESPECTIVELY <ENTER> to continue <EXIT> to return Forbidden area Projected raster CRT faceplate border...
- Page 30 CRT PROJECTION ANGLE ADJUSTMENT CRT PROJECTION ANGLE IS THE FIRST STEP OF STATIC CONVERGENCE ADJUSTMENT. IT IS CRITICAL THAT THE RASTERS ARE CENTERED ON THE CRT FACE PLATES PRIOR TO PERFORMING THIS STEP. <ENTER> to read more <EXIT> to return CRT PROJECTION ANGLE ADJUSTMENT DURING THIS PROCEDURE,...
- Page 31 PROJECTION ANGLE ADJUSTMENT Align crosshairs <ENTER> continue <EXIT> to return (SW1 > SW2) 370b...
- Page 32 1. TURN THE SCREW MARKED 01 TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (bottom) TO RIGHT (top). 2. TURN THE SCREW MARKED 00 TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (top) TO RIGHT (bottom) <ENTER> to continue <EXIT> to return LENS CORNER FOCUSING CENTER FOCUSING...
- Page 36 • •...
- Page 37 Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. <EXIT> to return • •...
- Page 38 é ê ç è é ê ç è • é ê • • • •...
- Page 39 • é ê • ç è é ê • ç è é ê • • • é ê • ç è é ê ç è é ê...
Need help?
Do you have a question about the R9000901 and is the answer not in the manual?
Questions and answers