The part number and serial number are located at the back side of the On safety projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding 1. This product should be operated from an AC power source. this product.
Page 8
Replacement parts - When replacement parts are required, be lightning storm, or when it is left unattended and unused for long sure the service technician has used original BARCO replacement periods of time, unplug it from the wall outlet. This will prevent damage parts or authorized replacement parts which have the same char- to the projector due to lightning and AC power-line surges.
Page 9
This dev ice complies with part 15 of S e e in s ta lla tio n in s tru c tio n s b e fo re c o n n e c tin g to th e s u p p ly . the FCC rules.
Page 11
Connections CONNECTIONS This dev ice complies with part 15 of S e e in s ta lla tio n in s tru c tio n s b e fo re c o n n e c tin g to th e s u p p ly . the FCC rules.
Page 12
Connections This dev ice complies with part 15 of S e e in s ta lla tio n in s tru c tio n s b e fo re c o n n e c tin g to th e s u p p ly . the FCC rules.
Page 18
Controlling Ceiling IR sensor Screen Front of projector Rear side of projector u rÃA 88 ÃÃS y r & R P S + 6 \ Q F P O WE R / M A I NS C O M M .
NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN 5976283 BARCOGRAPHICS 808s 160501...
Page 22
Start Up of the Adjustment Mode 5976283 BARCOGRAPHICS 808s 160501...
Service Mode SERVICE MODE ENTER ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS ENTER EXIT Select with é or ê SERVICE MODE then <ENTER> IDENTIFICATION COPY A BLOCK <EXIT> to return. DELTE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE...
Page 42
Service Mode ENTER SERVICE MODE IDENTIFICATION COPY A BLOCK DELTE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE RUN TIME SET TO MIDPOSITION CONVERGENCE MID DYNAMIC ASTIGMATISM MORE... Select with then <ENTER> <EXIT> to return. GRAPHICS 809 SP Proj. address : 001 Soft.
Page 43
Service Mode ENTER SERVICE MODE IDENTIFICATION COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE RUN TIME SET TO MIDPOSITION CONVERGENCE MID DYNAMIC ASTIGMATISM MORE... Select with é ê then <ENTER> ENTER <EXIT> to return. DELETE MODE Nr.
Page 44
Service Mode ENTER SERVICE MODE IDENTIFICATION COPY A BLOCK è ç DELTE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE RUN TIME SET TO MIDPOSITION CONVERGENCE MID DYNAMIC ASTIGMATISM ENTER MORE... Select with EXIT then <ENTER> <EXIT> to return. PASSWORD Enter new password : 0 0 0 0...
Page 45
Service Mode ENTER SERVICE MODE IDENTIFICATION COPY A BLOCK DELTE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE RUN TIME SET TO MIDPOSITION CONVERGENCE MID DYNAMIC ASTIGMATISM MORE... Select with ENTER EXIT then <ENTER> <EXIT> to return. SET TO MIDPOSITION All settings in current block will be overwritten !
Page 46
Service Mode Spot shapes before dynamic astigmatism correction ENTER Diagonal Spot shapes astigmatism correction after dynamic EXIT (use the astigmatism correction arrow key) Axial astigmatism correction (use the arrow key) SERVICE MODE IDENTIFICATION ENTER COPY A BLOCK DELTE A BLOCK DELETE ALL BLOCKS CHANGE PASSWORD CHANGE LANGUAGE...
Page 47
<ENTER> SAFETY <EXIT> to return. NOTICE ENTER RISK OF ELECTRICAL SHOCK EXIT G2 ADJUSTMENT SHOULD BE PERFORMED BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS. IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN. ENTER SERVICE MODE...
Page 48
Service Mode é ê ENTER SERVICE MODE G2 ADJUSTMENT GAMMA CORRECTIONS CRT RUN IN CYCLE PROJECTOR WARM UP CRT DRIVE MODE MORE... ENTER Select with then <ENTER> <EXIT> to return. PROJECTOR WARM UP OPTION : ON A FULL WHITE PATTERN WILL BE GENERATED FOR 20 MINUTES AT POWER UP AFTER THIS PROCEDURE...
Messages, warnings and failure codes MESSAGES, WARNINGS AND FAILURE CODES WARNING : SOURCE 01 Fh= 15.6 kHz source not Fv= 050 Hz available WARNING : SOURCE 01 Fh= 15.6 kHz When a wrong key is pressed on invalid the RCU. Fv= 050 Hz key entry WARNING :...
Page 50
Messages, warnings and failure codes WARNING : FAILURE Projector will switch to 'stand- Serial communication error be- RCVDS com- by' when the RCVDS is no longer tween RCVDS and projector. go to munication available. stand by WARNING : FAILURE The entered frequency or ap- invalid RWI commu- plied frequency of the source is...