Download Print this page

Operation - Craftsman 11533 - 9.6 Volt Cordless Model Operator's Manual

3/8-in. variable speed / reversible
Hide thumbs

Advertisement

OPERATION

FORWARD / REVERSE SELECTOR SWITCH with POWER LOCK-OFF (Fig. 2)
Fig. 2
a.
b.
POWER LOCK-OFF
FORWARD
The direction of bit rotation is forward or reverse and is controlled by a selector switch
located above and to the rear of the trigger switch. When holding the drill / driver in the
normal operating position, (and viewed from the back of the drill/driver see Fig 2 a, b, c),
the selector switch should be positioned (pushed) all the way to the RIGHT, for
FORWARD (b) or normal drilling / driving, and positioned (pushed) all the way to the LEFT
for REVERSE (c) to remove drill bits and back out screws.
The third position for the selector switch is located in the CENTER (a). This position keeps the
trigger switch from working, locking the power "OFF". Setting the selector switch in the "OFF" or
CENTER position helps reduce the possibility of accidental starting when the tool is not in use.
CAUTION:
!
To prevent gear damage, always allow the chuck to come to
a complete stop before changing the direction of rotation.
REMOVE BATTERY PACK FROM
DRILL / DRIVER (Fig. 3)
1. Place the Forward / Reverse Selector
Switch with Power Lock-Off into the
center position to lock the power off
(see Fig. 2, above).
2. Locate the latches on each side of the
battery pack. Depress (squeeze in)
latches and pull battery pack out of
drill.
14
OPERATION cont.
CHARGING THE BATTERY PACK (Fig. 4 and 4a)
The battery pack for this tool has been shipped in a low charge condition to prevent
possible problems. Therefore, you should charge overnight prior to use.
c.
NOTE: Batteries will not reach full charge the first time they are charged.
Allow several cycles (operation followed by recharging) for them to become
fully charged.
1. Charge battery pack only with the charging
stand/ transformer that was supplied with
this drill / driver.
2. Make sure power supply is normal
household voltage, 120 volts,
60 Hz, AC only.
REVERSE
3. Connect charging stand's transformer to power
supply.
4. Place battery pack in charging stand. Align
raised rib on battery pack with groove in
charging stand (See Fig. 4).
5. Press battery pack down into charging stand
making sure contacts are engaged properly.
6. The charging stand has two (LED) indicator
lights, one green and one red.
When the charging stand's transformer is
plugged into a power outlet, the green LED
will light, indicating that the charger is
operating properly.
When a battery pack is put into the charging
stand/transformer, the red LED will light,
indicating that the battery pack is charging
Fig. 3
properly (see Fig. 4a).
Both lights will remain "On" as long as
the charging stand/transformer is plugged
in and the battery pack is charging.
When the battery pack is charged and removed from the charging stand, the red light
will go Off. The green LED will stay "On" as long as the charging stand/transformer
is plugged into a power supply and operating properly.
NOTE: If the charging stand LED lights do not operate properly, or the charging
stand does not charge the battery pack, return the drill/ driver, charging
stand/transformer and battery pack to your nearest Sears store or other
Craftsman outlet to have it replaced.
7. After normal use, 3 hours or less of charging time is required to fully recharge battery
pack. If battery pack is completely discharged, 6 hours or longer of charging time is
required to fully recharge battery pack.
Fig. 4
Green
LED
Fig. 4a
Red
LED
Green
LED
15
10-4-07 Drill
10300-10400

Hide quick links:

Advertisement

loading

  Related Manuals for Craftsman 11533 - 9.6 Volt Cordless Model

This manual is also suitable for:

172.10300172.10400