3/8 in., 14.4 volt cordless drill-driver variable speed/reversible (20 pages)
Summary of Contents for Craftsman NEXTEC 320.30565
To reduce the risk of injury, • Assembly the user must read and understand • Operation • Maintenance the Operator's manual before using • Espa_ol this product. Charge battery before first use, Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.craftsman.com...
Troubleshooting Page 24 Exploded View and Parts List Pages 25-26 CRAFTSMAN ONE YEAR LIMITED WARRANTY FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship. With proof of purchase, defective product will be replaced free of charge.
The purpose of safety symbols is to attract you attention to possible dangers. The safety symbols and the explanations with them deserve your careful atten- tion and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes proper accident...
SAVE THESE INSTRUCTIONS Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current...
GENERAL POWER TOOL SAFETY WARNINGS A_, WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. The term "power tool" in all of the warnings listed below refers to corded power tools or battery-operated (cordless)
PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories, blades, etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.
Do not place the drill/driver or battery pack near fire or heat. They may explode. Use only the recommended the battery pack 320.11221 and charger 320.29497, 320.14300, 320.10006. Any attempt to use another battery pack will cause damage to the drill/driver; it could possibly explode or cause a fire or personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the drill/driver in unexpected situations. Do not use on a ladder or unstable support. For best results, your battery pack should be charged in a location where the temperature is more that 32°F (0°C) but less that 104°F (40°C).
ID]=_.'_o_l[o_] KNOW YOUR REVERSIBLE DRILL/DRIVER (Fig.l) Fig. 1 Torque-Adjustment Ring Two-speed Gearbox Switch 3auge Keyless Chuck Direction-of-Rotation Worklight Selector (Forward/Center Lock/Reverse) Trigger Switch _/Pack Battery- Release Button PRODUCT SEPCIFICATION Chuck 3/8-in. Motor 12 Volt DC LO 0-400/HI 0-1300 RPM No-Load Speed Clutch 18 Position...
_L. WARNING: The safe use of this product requires an understanding of the information on the tool and in this operator's manual, as well as knowledge the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.
_h, WARNING: If any parts are broken or missing, do not attempt to plug in the power cord or operate the drill/driver until the broken or missing parts are replaced. Failure to do so could result in possible serious injury. WARNING: Do not attempt to modify this drill/driver or create accessories recommended...
LOW-BATTERY CAPACITY INDICATOR • If the FuelGauge shines red when the trigger switch on the drill/driver depressed it means that the battery pack power has run out and the battery pack should be recharged. Unlike other battery-pack types, Lithium-Ion battery packs deliver fade-free power for their entire run time.
Due to Lithium-Ion fade-free properties, the only time it is necessary to charge the Lithium- Ion battery pack is when the pack has reached the end of its charge. To signal the end of charge, power to the tool will drop quickly and the FuelGauge LED will flash rapidly.
VARIABLE SPEED (Fig.3) The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. DIRECTION-OF-ROTATION SELECTOR (FORWARD/CENTER LOCK/ REVERSE) (Fig. 3) The direction of bit rotation is reversible and is controlled by a selector located above the trigger switch.
TWO-SPEED GEARBOX (Fig. 5} Fig. 5 The drill/driver has a two-speed gearbox for drilling or driving at LO or HI speeds. A slide switch is located on the top of the drill/driver to select either LO or HI speed. When using drill/driver in the LO speed range, the speed will decrease...
For delicate operations, such as removing a partially stripped screw, use a low torque setting. For operations such as drilling into hardwood, use a higher torque setting. NOTICE: When adjusting torque clutch make sure that I Fig. 7 Drill icon Torque indicator the speed switch is either com-...
INSTALLING BITS (Fig. 10) Fig. 10 Keyless chuck UNLOCK Lock the trigger switch (release) placing the direction-of- rotation selector in the OFF Drill 6it (center lock) position. Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
DRILLING (Fig. 12) Fig. 12 Check that the direction- of-rotation selector is at the correct setting (forward or reverse). Secure the material to be drilled in a vise or with clamps to keep it from turn- ing as the drill bit rotates. Hold the drill/driver firmly, and place the bit at the...
METAL DRILLING For maximum performance, use high speed steel bits for metal or steel drilling. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance. WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: It is not recommended to use compressed...
• Exterior may be cleaned with a cloth or soft non-metallic brush. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve natural resources, please recycle or dispose of batteries properly. This product con- tains lithium-ion batteries. Local, state, or federal laws may prohibit disposal of lithium-ion batteries in ordinary trash.
Insert the hex key into Fig. 15 the chuck and tighten the chuck jaws securely. Tap Mallet sharply with a mallet in a counterclockwise direction. This will loosen the chuck Keyless chuck on the spindle. It can now be unscrewed by hand.
PROBLEM CAUSE SOLUTION The drill/driver does not work Battery is depleted Charge the battery Bit cannot be installed Chuck is not open Open the chuck Be sure cooling vents Clean, clear vents. Do Motor overheating are free from saw dust not cover vents with and obstacles hand during operation...
°__. m 6, r" :::r --o < ¢,/) ,.-I- Co 23- _-__. r'--...
12.0 VOLT LITHIUM-ION CORDLESS 3/81N. REVERSIBLE DRILL MODEL NO. 320. 30565 The Model Number will be found on the Nameplate attached to the handle of the Worklight. Always mention the Model Number when ordering parts for this tool. 2790263000 Gear Case Assembty 2790265000 Motor and Gear Assembty 3126210000...