Page of 20
PERATOR'S MAN
AL
®
1/2 in. 19.2 VOLT CORDLESS DRILL-DRIVER
VARIABLE SPEED/REVERSIBLE
Model Nos.
315.114852
315.114853
A
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Craftsman
Consumer
Helpline:
1-800-932-3188
Sears, Roebuck
and Co., 3333 Beverly Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-848
12123-08 (REV:07)
Save this
manual
for future
reference

   Summary of Contents for CRAFTSMAN 315.114852

  • Page 1

    Craftsman Consumer Helpline: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman 983000-848 Save this manual for future reference 12123-08 (REV:07)

  • Page 2

    FREE REPAIR (or rep(acement if repair proves impossib(e). If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

  • Page 3

    [] Avoid accidental starting. Be sure switch is in the WARNING!READ AND UNDERSTAND ALL locked or off position before inserting battery pack. INSTRUCTIONS. Failure to follow all instructions Carrying tools with your finger on the switch or insert- listed below may result in electric shock, fire and/or ing the battery pack into a tool with the switch on serious personal injury.

  • Page 4

    Use only accessories that are recommended by the SERVICE manufacturer for your model. Accessories that may Tool service must be performed only by qualified be suitable for one tool may create a risk of injury when repair personnel. Service or maintenance performed used on another tool.

  • Page 5

    [] An extension cord should not be used unless WARNING! READ AND UNDERSTAND ALL absolutely necessary. Use of improper extension INSTRUCTIONS. Failure to follow all instructions cord could result in a risk of fire and electric shock. If listed below, may result in electric shock, fire and/or extension cord must be used, make sure: serious personal injury.

  • Page 6

    Someof the following symbolsmaybe usedon this product.Please studythemandlearntheir meaning. P roper interpretation ofthesesymbols will allowyouto operate theproductbetterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Current Amperes Hertz Frequency (cycles per second) Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current No Load Speed...

  • Page 7

    If you do not understand the warnings and your nearest SEARS PARTS AND REPAIR SERVICE instructions in the operator's manual, do not use this CENTER for repair. When servicing, use only identical product. Call the Craftsman Consumer Helpline at replacement parts. 1-800-932-3188 for assistance.

  • Page 8

    PRODUCT SPECIFiCATiONS Clutch ..............24 Position Chuck ............1/2 in. Keyless Motor ............... 19.2 Volt DC Torque ..............410 in.lb. Switch ......VSR (Variable Speed Reversible) Charger Input ........120 V, AC only, 60 Hz Gear Train .............. 2 Speed Charge Rate .............

  • Page 9

    KNOW YOUR DRILL DRIVER KEYLESS CHUCK See Figure 1. The keyless chuck allows you to hand-tighten or release The safe use of this product requires an understanding the drill bit in the chuck jaws. the information on the product and in this operator's manual LEVELS as well as a knowledge of the project you are attempting.

  • Page 10

    This product will accept DieHard_ 19.2 V lithium-ion bat- Failure to do so could result in objects being thrown tery packs and Craftsman 19.2 V nickel-cadmium battery into your eyes, resulting in possible serious injury.

  • Page 11

    BATTERY PROTECTION FEATURES [] Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the DieHardo 19.2 V lithium-ion battery packs are designed charger. with features that protect the lithium-ion cells and [] Normally the red LED on charger will come on.

  • Page 12

    CHARGING A HOT BATTERY PACK TO iNSTALL BATTERY PACK See Figure 3. When using the product continuously, the batteries in the battery pack will become hot. You should let a hot bat- [] Lock switch trigger on the drill by placing the direction tery pack cool down for approximately 30 minutes before of rotation selector in center position.

  • Page 13

    To stop the drill, release the switch trigger and allow the WARNING: Battery tools are always in operating chuck to come to a complete stop. condition. Therefore, switch should always be locked NOTE: The drill will not run unless the direction of rotation when not in use or carrying at your side.

  • Page 14

    TWO=SPEED GEAR TRAIN ADJUSTABLE TORQUE CLUTCH See Figure 6. This product is equipped with an adjustable torque clutch for driving different types of screws into different The drill has a two-speed gear train designed for drilling or materials. The proper setting depends on the type of ma- driving at LO (1) or HI (2) speeds.

  • Page 15

    INSTALLINGBITS REMOVING BITS See Figure 8. See Figure 8. [] Lock the switch trigger by placing the direction of [] Lock the switch trigger by placing the direction of rotation selector in the center position. rotation selector in the center position. [] Open or close the chuck jaws to a point where the [] Open the chuck jaws.

  • Page 16

    DRILLING See Figures 11 - 12.. Levels are located on the top and end of the motor housing to help keep the drill bit level during use. [] Check the direction of rotation selector for the correct setting (forward or reverse). [] Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.

  • Page 17

    WARNING: When servicing, use only identical Avoid using solvents when cleaning plastic parts. Most Craftsman replacement parts. Use of any other part plastics are susceptible to damage from various types of may create a hazard or cause product damage. commercial solvents and may be damaged by their use.

  • Page 18

    CHUCK REMOVAL See Figures 13- 15. MALLET The chuck may be removed and replaced by a new one. [] Lock the switch trigger by placing the direction of rota- tion selector in center position. [] Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely.

  • Page 19

    CRAFTSMAN 1/2 in., 19.2 VOLT CORDLESS DRILL-DRIVER MODEL NOS. 315.114852 and 315.114853 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your DRILUDRiVER or when ordering repair parts,...

  • Page 20

    Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.

This manual also for:

315.114853

Comments to this Manuals

Symbols: 0
Latest comments: