Keyfobs (Kf-234; Introduction; Specifications; Enrollment - Visonic Fully supervised wireless accessories Accessories Manual

KF-234 PG2
KEYFOBS (KF-234 PG2)
Wireless PowerG 2-Way Keyfob

1. INTRODUCTION

KF-234 PG2 is a
PowerG 4-button (6-function)
keyfob, designed for use with the
PowerMax10-G2.
Transmission is initiated
pressing any one of the four
recessed pushbuttons.
pressing a specific button, the KF-
234 PG2 transmits a PowerG
message associated with the
button that was pressed and
identifiable by PowerMax10-G2
control panels.
A red LED lights during transmission. When an identified
command is received by the PowerMax10-G2 control
panel, it acknowledges
acknowledgement, the green LED lights and a happy beep
is heard to indicate successful completion of the command
or the red LED lights and a sad beep is heard to indicate
that the control panel cannot perform the command.
In addition, a battery report is transmitted with the outgoing
message. PowerMax10-G2 control panels are designed to
identify this report and operate a corresponding output, if
required.
Each keyfob is supplied with a small key ring.

3. ENROLLMENT

Refer to the PowerMax10-G2 Installer Guide for the device enrollment procedure.

4. MODIFY DEVICE SETTINGS

This section describes how to configure the parameters for home monitoring of people from the PowerMax10-G2 control
panel.
To Modify the Keyfob Device Settings
Refer to the PowerMax10-G2 Installer Guide and perform the procedure for Adding A Wireless Device (section 4.4.2), or,
Modifying a Device (section 4.4.5). Then continue below to modify the device settings.
1.
When the PowerMax10-G2 display reads [DEV SETTINGS], press
The PowerMax10-G2 display will read [AUX A].
2.
Press the
I OK
The PowerMax10-G2 display will read [instant
3.
Press the
"skip exit delay" and "PGM", for example, "PGM".
4.
Press to confirm the selection.
I OK
The PowerMax10-G2 display will revert to [AUX A].
2
miniature
by
Upon
Figure 1:
External View
the command.
button.
or button repeatedly to select between "instant",
Operating power is obtained from an internal 3V Lithium
battery.

2. SPECIFICATIONS

Frequency Band (MHz): Europe: 433, 868, USA: 915
Modulation: GFSK 50kbs, 25 kHz deviation
Antenna: Built-in helical antenna
Communication Protocol: PowerG
Battery type: 3V CR-2032 Lithium battery
Caution! Risk of explosion if battery is replaced by an
incorrect type. Dispose of used battery according to
manufacturer's instructions.
Battery Life Expectancy: 8 years (for typical use)
Note: If transmission is still possible despite the battery
condition, the unit will send a low battery signal to the
control panel.
Transmitted Messages: Arm Away, Arm Home, Arm
Upon
Latchkey, Disarm, AUX and Panic.
Operating Temperature: 0° to 55°C (32° to 131°F)
Dimensions: 60 x 34.5 x 12.5 mm (2-3/8 x 1-3/8 x 1/2 in.)
Weight (including battery): 25 g (0.9 oz)
Color: Black
Compliance with Standards:
Europe: EN 300220, EN 50131-1 Grade 2, Class II and
(EN 50134-2 Class II if used for social alarm), EN 301489,
EN 50130-4, EN 60950
USA: CFR47 Part 15
Canada: RSS 210
I OK
].
.
I OK
AUX A
I OK
instant
or
PGM
I OK
PGM
AUX A
D-302758