Rate Of Fire Adjustments And Troubleshooting; Velocity Adjustment - Tippmann BRAVO ONE SERIES Owner's Manual

Hopper Installation (continued from page 7)
blocking device installed and safety in Safe Mode, you are now ready to
load your hopper with paintballs. Fill the hopper and only remove the
E
barrel blocking device and turn off the safety when ready to shoot.
N
STEP 4) Rate of Fire Adjustments and Troubleshooting
• For markers with E-Trigger
G
Instructions (on pages 8-10); before performing STEP 5.
L
• For markers without E-Trigger
I
STEP 5) Velocity Adjustment
Each time you play paintball, the velocity of your
S
paintball marker should be checked with a
H
chronograph, an instrument for measuring
velocity, prior to playing paintball to verify that
the marker's velocity is set below 300 feet per
second or less if required by playing field.
To adjust the velocity use the 3/16" allen wrench
marker. The velocity adjustment screw is located on left side receiver. To
adjust the velocity down, turn the screw inward or clockwise
the velocity up, turn the screw out or counterclockwise
the velocity screw.
TM
E-TRIGGER OPERATING INSTRUCTIONS
Read and follow the E-Trigger
completely before installing the air supply cylinder as outlined in - Getting
Started - STEP 2: on page 7.
READ EACH STEP COMPLETELY BEFORE PERFORMING THE STEP:
INSTALL THE AIR SUPPLY AND LOAD THE HOPPER WITH PAINTBALLS ONLY
AFTER YOU:
❏ ❏ ❏ ❏ ❏ HAVE THE BARREL BLOCKING DEVICE INSTALLED (SEE PAGE 2) ;
❏ ❏ ❏ ❏ ❏ HAVE THE SAFETY IN THE "SAFE" POSITION ( SEE PAGE 4);
❏ ❏ ❏ ❏ ❏ HAVE SUCCESSFULLY INSTALLED THE BATTERY (STEP 2: ON PAGE 9)
AND ❏ ❏ ❏ ❏ ❏ ARE FAMILIAR WITH THE E-TRIGGER
ON PAGE 9).
❏ Eye protection designed for paintball use must be worn by the user
and any person within range.
STEP 1: Prepare the marker for safety before any programming:
Prepare the marker for disassembly. First follow ❏ Unloading Your Marker
and ❏ Air Supply Cylinder Removal instructions on page 14. Never
disassemble this marker while it is pressurized with air. Do not pressurize
a partially assembled marker.
TM - read and follow E-Trigger TM
TM - go to STEP 5.

Velocity Adjustment

included with your
. Do not remove
TM Operating Instructions (on pages 8-10)
WARNING
TM NORMAL OPERATION (STEP 3:
8
E-Trigger TM Operating Instructions
(continued on page 9)
E-Trigger TM
STEP 2: E-Trigger
• Remove Battery Clip/old battery (from marker). ❏ Remove the 2
bolts
cutout bringing non-connected end out first. As you remove the battery
Operating
from the receiver, do not pull the wires off of the internal components.
❏ Carefully remove the old battery from battery clip connector.
• Install new battery. ❏ Attach 9 volt battery to the
battery connector and be sure wires lay flat inside
Screw
the cutout area of receiver (as shown on page 19).
3/16" Allen
❏ Carefully tilt and insert your new battery, wire
Wrench
attached end first, into receiver as shown
❏ Reinstall left receiver grip with 2 grip bolts.
Battery installation is complete.
NOTE: The E-Trigger Low Battery Indicator feature: the "Ready To Fire"
solid Green LED will turn to red when the battery is low and needs replaced.
. To turn
STEP 3: NORMAL OPERATION:
❏ ❏ ❏ ❏ ❏ 1) To Turn ON the E-Trigger to normal operation - Ready To Fire:
Without holding the trigger: Use a small object like
an allen wrench
power button
green LED light
the power button.
❏ Your marker is now ready for normal operation
in the SEMI-AUTO Firing Mode: 1 pull of the trigger fires 1 time (This is
the Factory Default Firing Mode Setting).
NOTE: If pressing the power button failed to turn on the LED light, see
troubleshooting on page 10.
❏ ❏ ❏ ❏ ❏ 2) To turn OFF the E-Trigger
power button until the LED turns off, then release the Power Button. NOTE:
The trigger electronics are set to shut-off automatically after a prolonged
period of inactivity.
❏ ❏ ❏ ❏ ❏ 3) To select a new firing mode: ❏ With the electronics turned on,
each press / release of the power button will change the firing mode to the
next firing mode in the menu: (the LED will flash 1, 2, 3 or 4 times to
identify the firing mode you have selected).
THE 4 FIRING MODES ARE:
Default firing mode:
1) SEMI-AUTO = 1 pull / release of the trigger fires 1 time.
❏ 1 flash of the LED light indicates SEMI-AUTO mode.
Operating Instructions (continued from page 8)
TM Battery Installation Or Replacement
). ❏ Carefully work battery out of receiver
and the left grip
to ❏ press and hold the
(for about 5 seconds) until the
comes on and then release
electronics. ❏ Press and hold the
TM
9
E
N
G
L
I
S
H
.
Power
Button
LED
THE 4 FIRING MODES ARE:
(continued on page 10)