Tippmann BRAVO ONE SERIES Owner's Manual page 11

Marker Disassembly / Assembly (continued from page 17)
Reassembling Receiver Halves:
STEP 1: ❏ Double check that the Trigger Assembly
E
; and other parts: Feed Elbow Lock
N
Bolt* ; Ball Latch ; Linkage Arm*
G Bolt* + Bolt Insert ; Bolt Handle
Pin* ; Buffer O-ring ; End Cap
L
Adapter Nuts ; are in place and (*=oiled) (see below and schematics
I
on pages 11–12 for details as needed).
❏ ❏ ❏ ❏ ❏ Non-E-Trigger
TM Markers go to STEP 2) on page 19.
S
H
For E-Trigger TM Markers:
Do not operate sear tripper assembly uninstalled as solenoid / armature
may pinch you.
❏ Double check that the E-Trigger
are positioned correctly for reassembly as
follows:
❏ 1) Place solenoid / (armature - fits
inside solenoid) into right receiver.
❏ 2) Carefully align and insert the
electronics board into slot.
❏ 3) Place trigger switch on two pins of
right receiver half.
❏ 4) Insert capacitor in slot.
❏ 5) Route wires in cutout areas to lay flat under armature pin and
battery and not be pinched when receiver halves are reassembled. ❏
Visually inspect internal wires for disconnected wire end(s) or damage.
❏ 6) Insert armature pin
❏ 7) Insert Magnet
in slot below armature as shown.
❏ Double check that all parts are in place as shown.
❏ Place battery connector
the magnet fits into left receiver half slot so it does not break and ❏
wires are not pinched as you ❏ place left half on right half so the
halves fit flush.
(E-Trigger TM Markers Go to STEP 2 on page 19).
+ Pin + Spring
; Link Arm Pins (2)
; Drive Spring*
+ End Cap Cover
E-Trigger TM Parts Not Shown
in Basic Parts List on
parts
TM
(pages 12-13)
TA01135 Sear
02-88
Sear Spring
TA06020 Armature Pin
TA09935
Electronics
Assembly
Solenoid
-Armature
TA05014 Magnet
into 2 slots so it moves freely.
through left receiver half ❏ make sure
18
Reassembling Receiver Halves:
(continued on page 19)
Reassembling Receiver Halves: (continued from page 18)
; Front
; Rear
+ Guide
; 2 Tank
Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
STEP 2: ❏ Carefully install the left receiver half (make sure halves fit flush).
❏ Insert 4 short receiver bolts
❏ If marker has a barrel shroud
❏ Insert 3 long receiver bolts
❏ Attach adapter
bolt goes in front). ❏ Apply marker oil onto the barrel o-ring, insert
the barrel
❏ Slide the feed elbow
holds it in place.
❏ E-Trigger
battery connector and be sure the wires lay flat inside
the cutout area of the receiver.
❏ Carefully tilt and insert the battery (wire attached end
first ) into the receiver.
❏ Install the left receiver grip
❏ Press in the 2 magazine tabs
magazine
it in place. NOTE: The magazine may be used to
store tools and lubricating oil for your marker (shown
with 2 allen wrenches
.
- insert it now.
and ❏ tighten
tighten 2 bolts
and carefully screw it in.
into the receiver and tilt up until the feed lock
Markers - Attach a 9 volt battery to the
TM
with 2 bolts
and slide the
up into the marker until the tabs lock
and oil).
19
E
N
G
L
I
S
H
6)
the 7 bolts / .
(NOTE: short adapter
.