Operation; Using The On-Screen Menus; X-400D/X-450D Osd Menu Structure - Runco XtremeProjection X-450d Installation & Operation Manual

To display the Main Menu, press the MENU button on the remote control or Dimension
Digital Controller front panel (Figure 2-4).
To select a menu item, use the
Digital Controller front panel to highlight it. Then, to confirm your selection, press ENTER
on the remote control or Dimension Digital Controller front panel.
The X-400d/X-450d OSD menus are arranged hierarchically, as shown in Figure 4-1.
Some menu options apply only to certain input signal types. For example, Phase and
Tracking can only be adjusted for RGB, Component video or SCART signals.
Composite 1
Composite 2
Composite 3
Component
Input Source
HD 1
HD 2
SCART
DisplayPort
16:9
4:3
Letterbox
VirtualWide
Aspect Ratio
Cinema
Virtual Cinema
Native
Auto Cinema
Screen
Screen 1 / Screen 2
Brightness
Contrast
Color
Picture
Tint
Sharpness
Noise Filter
Left/Right
Up/Down
Width
Height
Overscan
Input Position
Overscan Mode
(Zoom/Crop)
Phase
(RGB/Component/SCART signals only)
Tracking
(RGB/Component/SCART signals only)
Recall ISF Night or ISF Day
Memory
Recall/Save Custom 1 or Custom 2
Presets
Reset Custom 1 and Custom 2 to Factory
Default
3D Mode
3D (Auto, Off, Side-by-Side, Top-and-Bottom or
Frame Packing)
Processing
Reverse Eyes
(On/Off)
Off, 30 Minutes, 60 Minutes, 90 Minutes, 2
Sleep Timer
Hours or 4 Hours
Signal
System
Information
Network
Field Service
Manufacturing
Figure 4-1. X-400d/X-450d OSD Menu Structure
Runco X-400d/X-450d Installation/Operation Manual
and buttons on the remote control or Dimension
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI 6
HDMI 7
HDMI 8
Calibration
Note: Default settings appear in bold type. Settings marked with an asterisk (*) apply to 2D content only.
Gain
Offset
Gamma
Display Color -
Common Settings
Color Temp
Color Gamut*
PCE*
Lamp
Display Color -
ConstantContrast*
Projector Settings
(X-400d only)
Brightness
Contrast
Input Image Color
Tint
Sharpness
Gain
Offset
Input Color
Chroma Delay
Noise Filter
Save ISF Night
Back / Confirm
Save ISF Day
Memory Preset
Copy/Paste
Aspect Ratio
Left/Right
Up/Down
Width
Output Shift
Height
Screen Masking
Corner Alignment
Image Alignment
Midpoint Alignment
Adjustment Mode Both, Primary or Secondary
Owner Name
ISF Calibrated
Splash Configure ISF Other
Splash Timer
Splash Enable
OSD Position Hor. / Ver.
61

4. Operation

4.1
Using the On-Screen
Menus
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35, 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Simple (5500K, 6500K, 7500K or 9300K)
Auto, REC709, SMPTE-C, EBU, Native or PCE
Red x, y / Green x, y / Blue x, y / White x, y
Yellow x, y / Cyan x, y / Magenta x, y
Power (230W or 260W)
On / Off
-50, -49 ... 0 ... 49, 50
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
0, 1, 2 ... 7
(Composite inputs only)
0, 1, 2 ... 63
Copy Settings
Paste Settings
Copy Settings
Paste Settings
-50, -49 ... 0 ... 49, 50
-50, -49, 48 ... 0
0, 1, 2 ... 100
(Top / Bottom / Left / Right /
Test Pattern Enable)
Top Left / Top Right / Bottom Left /
Bottom Right / Test Pattern Enable
Center / Top Middle / Left Middle /
Right Middle / Bottom Middle /
Test Pattern Enable
5, 6, 7 ... 15 ... 59, 60
On/Off
0, 1, 2 ... 100
Operation