Midi Control; Midi Controller Setup; Assigning Controls; Midi Platters - Rane SIXTY-ONE Operator's Manual

3. Move the Parameter Knob to the
position that you want the to be
the lowest value of the parameter.
4. Press the Macro Min button to set
the minimum position.
5. Move the Ultra or Super Knob to
the position that you want the
parameter to end being
controlled from.
6. Move the Parameter Knob to the
position that you want the to be
the highest value of the parameter.
7. Press the Macro Max button to set
the maximum.
8. Link the parameter to the Ultra or
Super Knob by pressing the Link
button.
Now when you adjust the Ultra or Super
Knob you will see the parameter knob
move within the range that you just
specified. Any parameters not customized
but linked to the Super or Ultra Knob will
behave as normal.
You can save any macro
mappings you have made to
an effect by clicking the Save button
by the Super Knob, and save effects
combinations made in Ultra Knob Mode
by clicking the Save button by the Ultra
Knob.
28

MIDI Control

The MIDI Control feature in Scratch Live
provides the ability to map MIDI controls
to Scratch Live controls, and thus control
the functions of Scratch Live using MIDI
controllers such as keyboards, triggers,
sliders, and knobs. Integrating MIDI
controllers into your Scratch Live setup
can improve live performance usability,
such as hitting pads on a MIDI controller
to trigger loops and cue points.

MIDI Controller Setup

The process of setting up a MIDI
controller for use with Scratch Live
will vary depending on the hardware in
question. Many devices can connect to
a computer using MIDI over USB, and
will either be supported directly by your
operating system, or require installation of
drivers and configuration utility software.
Follow the manufacturers instructions for
installation.
Other controllers may solely use a MIDI
out connector to send control messages,
and will require a separate MIDI interface
unit to communicate to software.
Generally the MIDI interface will come with
drivers and configuration tools which pass
your controller's output onto an available
MIDI channel, which can be used by
Scratch Live.
Once your controller is installed and
functioning correctly, use these directions
for assigning controls.

Assigning Controls

To enable MIDI assign mode,
click the MIDI button. Hovering
the mouse pointer over a control will bring
RANE SIXTY-ONE MIXER FOR SERATO SCRATCH LIVE • OPERATOR'S MANUAL 2.4.4
up the MIDI assignment box, showing the
current assignment status.
To assign a MIDI control, click on the
control in Scratch Live, then move the
MIDI control. The MIDI assignment box
should update to show it has mapped the
controls to one-another.
To un-assign a MIDI control, click on the
control in Scratch Live, and press return
on your computer keyboard.
While in MIDI assign mode, controls
which have MIDI inputs assigned show a
green box indicator around them.
NOTE: Once in MIDI assign mode,
Scratch Live controls will no longer
respond directly to the mouse. If you
need to change a control using the
mouse, disable MIDI assign mode.

MIDI Platters

The Scratch Live Virtual Decks are not
user assignable to MIDI control. MIDI
devices with platters on them all send
different data so user mapping is not
possible. To control the platter use a
natively supported controller.
Assigning MIDI to Other Controls
Controls which
are not normally
visible are available for assignment when
in MIDI assign mode by clicking on the
Show MIDI Panel button. This will open
up a panel allowing MIDI assignment for
controls including library navigation as
well as additional Deck functions such as
fine pitch control and extended cue and
looping features.

Ctrl-Click Functionality

Some Scratch Live controls on the GUI
have additional functionality assigned
to ctrl-click. You can assign ctrl-click
functionality to a MIDI control, alongside
the normal functionality. For example, ctrl-
click on the INT mode pitch slider returns
pitch to zero. To assign this to MIDI
control, enter MIDI assign mode, ctrl-click
on the slider, and then assign one of the
pads to it. When you press the pad, pitch
goes to 0.