Dj-Fx Plugin; Ultra Knob Mode; Super Knob Mode; Effects Bpm Multiplier - Rane SIXTY-ONE Operator's Manual

DJ-FX Plugin

The DJ-FX Plugin gives you control of
two FX units, each with three chained
effects slots per unit. Each FX unit has
two control modes: Ultra Knob Mode and
Super Knob Mode, both of which can be
fully customized. The DJ-FX plugin opens
in Ultra Knob Mode by default.
The DJ-FX Plugin must be enabled in
the Plugins tab in the setup screen. Once
enabled, the DJ-FX panel button appears
in the panels area on the main screen.
See "Enable DJ-FX" on page 39.
To enable post-fader DJ-FX with the
InsERT button, see "Enable Mixer
DJ-FX Send" on page 39.
NOTE: The DJ-FX plugin is not visible
if your Rane hardware is not connected.

Ultra Knob Mode

Click the Ultra Knob Mode
button to select Ultra Knob
Mode. This allows you to control up to
three effects slots in one FX unit using the
one Ultra Knob.
Click on the drop down menu to load an
Ultra Knob effect. (This is "empty" before
settings are saved in Macro Edit Mode.)
Click the ON button to enable the effect,
and use the Ultra Knob to control the wet
and dry amount of all effects.
Click the Show Parameters button
to show the effects and parameters
that are controlled by the loaded
Ultra Knob preset.
RANE SIXTY-ONE MIXER FOR SERATO SCRATCH LIVE • OPERATOR'S MANUAL 2.4.4

Super Knob Mode

Super Knob Mode allows you
individual control of each effect in
the FX unit. Each effect slot has a Super
Knob which controls the wet and dry
amount for the effect.
Click the Effects drop down box to
select an effect for the effect slot. You can
leave a slot empty by selecting "empty."
Click the ON button by the Super
Knobs to toggle turning the effect(s) on
and off.
The effects chain works in series going
from effects slots 1 to 3. The effected
audio from slot 1 passes through slot 2,
which is then passed through slot 3.

Effects BPM Multiplier

The Effects BPM
Multiplier is used to
adjust the effect time. The effect time is
set using the track's BPM value, but by
applying the Effects BPM Multiplier you
can increase or decrease the effect time.

Deck Assign

You can select which Deck the FX unit
applies to by clicking the Deck buttons.
Each Deck can only pass through one FX
unit at a time. You can assign the Sixty-
One PGM FlexFX buttons control DJ-FX:
in the Plugins tab of the Setup screen,
turn on "Enable Mixer DJ-FX Send" on
page 39. The software Deck buttons
are not visible with this enabled.

Show Parameters

Press the Show Parameters button
to expose the individual parameters
for each effect. You can then control
the individual parameters by adjusting
their respective knobs.
In Ultra Knob Mode, use this to select
which effects are loaded and controlled by
the Ultra Knob.
In Ultra and Super Knob Mode, you
can link or unlink a parameter to the
Super Knob by pressing the Link Button,
allowing one master control of some
parameters and individual control of
others.

Macro Edit Mode

Macro Edit Mode is an advanced
option that allows you to create
macro mappings for each effect and to
save any effects edits made in Ultra or
Super Knob Mode. Open Macro Edit
Mode by clicking the Macro Edit Button
while Show Parameters is open. Once
opened, more controls appear which
allow you to create and change parameter
mappings.
To map a parameter to the Ultra or Super
Knob:
1. Unlink the parameter that you
want to map to the knob. The
Macro Min and Max buttons for this
parameter are now displayed.
2. Move the Ultra or Super Knob
to the position that you want the
parameter to start mapping from.
27