Dell Broadcom NetXtreme Family of Adapters User Manual page 176

BASP BIND BASP_1_V2_EII B57_2_EII
# Bind protocols to BASP.LAN.
BIND IP BASP_1_V2_EII ADDR=192.168.2.200 MASK=255.255.255.0
BIND IP BASP_1_V3_EII ADDR=192.168.3.200 MASK=255.255.255.0
BIND IP BASP_1_V4_EII ADDR=192.168.4.200 MASK=255.255.255.0
mount all
NOTE: If you modify any adapter parameters, you must reboot the system before the changes takes effect. If you make
changes and do not reboot, you may experience configuration problems.
Example of Multiple SLB TEAMs with Multiple Frame Types
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_EII VSLOT=1
LOAD BASP.LAN FRAME=ETHERNET_802.2 NAME=BASP_1_E82 VSLOT=1
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_2_EII VSLOT=2
LOAD BASP.LAN FRAME=ETHERNET_802.3 NAME=BASP_2_E83 VSLOT=2
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_1_EII SLOT=1
LOAD B57.LAN FRAME=ETHERNET_802.2 NAME=B57_1_E82 SLOT=1
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_2_EII SLOT=2
LOAD B57.LAN FRAME=ETHERNET_802.2 NAME=B57_2_E82 SLOT=2
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_3_EII SLOT=3
LOAD B57.LAN FRAME=ETHERNET_802.3 NAME=B57_3_E83 SLOT=3
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_4_EII SLOT=4
LOAD B57.LAN FRAME=ETHERNET_802.3 NAME=B57_4_E83 SLOT=4
BASP BIND BASP_1_EII B57_1_EII
BASP BIND BASP_1_EII B57_2_EII
BASP BIND BASP_2_EII B57_3_EII
BASP BIND BASP_2_EII B57_4_EII
BIND IP BASP_1_EII ADDR=172.16.1.100 MASK=255.255.0.0
BIND IPX BASP_1_E82 NET=ABAB
BIND IP BASP_2_EII ADDR=172.18.1.100 MASK=255.255.0.0
BIND IPX BASP_2_E83 NET=BEEF
NOTE: When B57_1_EII is bound to BASP_1_EII, B57_1_E82 is also bound to BASP_1_E82. IPX load balance works only
with an all-Broadcom adapter or an all-Alteon adapter configuration. Values for VLSOT range from 1 to 4 (only four teams can
be configured).
Example of VLAN with BASP
LOAD ODINEB.NLM
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_V100_EII VSLOT=1 VLAN=100
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_V200_EII VSLOT=1 VLAN=200
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_V300_EII VSLOT=1 VLAN=300
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_1_EII SLOT=1
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_2_EII SLOT=2
BASP BIND BASP_1_V100_EII B57_1_EII
BASP BIND BASP_1_V100_EII B57_2_EII
BIND IP BASP_1_V100_EII ADDR=172.16.210.1 MASK=255.255.0.0
BIND IP BASP_1_V200_EII ADDR=172.17.220.1 MASK=255.255.0.0
BIND IP BASP_1_V200_EII ADDR=172.18.230.1 MASK=255.255.0.0
NOTE: When B57_1_V100_EII is bound to B57_1_EII, B57_1_EII is also bound to the other VLANs on the same VSLOT.
VLAN refers to the VLAN ID, and valid value for VLAN ID ranges from 1 to 4094.
Example of TRUNKING with BASP
LOAD ODINEB.NLM
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_EII VSLOT=1 MODE=TRUNK
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_1_EII SLOT=1
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_2_EII SLOT=2
BASP BIND BASP_1_EII B57_1_EII
BASP BIND BASP_1_EII B57_2_EII
BIND IP BASP_1_EII ADDR=172.16.210.1 MASK=255.255.0.0
NOTE: Switch ports must be configured for trunking (for example: FEC or GEC for Cisco switches)
Example of GVRP with BASP
LOAD ODINEB.NLM
LOAD BASP.LAN FRAME=ETHERNET_II NAME=BASP_1_EII VSLOT=1 VLAN=100 GVRP
LOAD BASP.LAN FRAME=ETHERNET_802.2 NAME=BASP_1_E82 VSLOT=1 LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_1_EII
SLOT=1
LOAD B57.LAN FRAME=ETHERNET_802.2 NAME=B57_1_E82 SLOT=1
LOAD B57.LAN FRAME=ETHERNET_II NAME=B57_2_EII SLOT=2
LOAD B57.LAN FRAME=ETHERNET_802.2 NAME=B57_2_E82 SLOT=2 BASP BIND BASP_1_EII B57_1_EII
BASP BIND BASP_1_EII B57_2_EII BIND IP BASP_1_EII ADDR=172.16.210.1 MASK=255.255.0.0
NOTES:
In this example, VLAN 100 is advertised to the switch using GVRP.