Table of Contents
Advertisement
IMPORTANT:
'I% operate
JVC's
video components
using this remole
control:
• You need to connect
JVC's
video components
through
the AV
COMPU
LINK,jacks
(see page 49) in addition
to the connections
using cables
with RCA pin plugs (see pages 10 to 12).
• Some JVC's
VCRs can accept two types of the control signal_
remole code "A" and "B?' Before using this remote control,
make
sure that the remote control code of the VCR connected
to the VCR 1
,jacks is set m code "A?'
- When another
JVC's
VCR is connected
to the VCR 2 or VIDEO
terminals,
set its remote
control
code to code "B." (This remole
control
cannot emit the control
signals
of code "B?')
• When using the remote
control,
aim the remole
control directly
at
the remote
sensor
on each component,
not on the receivec
O
bt_
,
s
c,o,_l;g,z
CHiLEVEL rqVOk
VCl20_
o
DOV,_
TU_I_G
VP
o
'_
o
JVC
RN_SRXSO2_J
_MOTE corcr_L
Note:
When you press one of the source selecting buttons, the
operation mode appears on the display windo_z For example,
the above illustration shows the remote control now works for
VCR 1 operation.
Buttons
Indications
VCR I
VCRI
DVD or DVD MULTI
DVD
TV/DBS
TV
CONTROL(repeatedly)*
_
VCRI
2
TAPE _
CDDSC
CDR
* Bypressing
CONTORL repeatedly, you can select "VCRI,"
"TAPE," "CDR" or "CDDSC" as the source.
VCR 1 (VCR
connected
to the
VCR 1 iacks]
You can always
perform
the following
opera/ions:
VCR1
0/I
:Turn on or offthe
VCR
1 (VCR connected
to
the VCR
1 ,jacks).
After pressing VCRI (or selecting "VCRI" by pressing CONTROL
repeatedly), you can perform the following operations on the VCR 1
(VCR connected to the VCR 1 ,jacks):
1-9,0
PLAY
REW
FF
• STOP
II PAUSE
REC PAUSE
CH +/-
:Select
the TV channels
on a VCR.
:Start playing.
:Rewind
a tape.
:Fast wind a tape.
:Stop playing
or recording.
:Pause playing. 'Ib resmne press I_ PLAY.
:Enter recording
pause by pressing
this button.
To start recording
again, press this button then
PLAY.
:Change
the TV channels
on the VCR.
Note:
You can use either VCR1 or CONTROL to activate the buttons listed
above, ff you press VCR1, the playing source also changes. On the
other hand, if you press CONTROL repeatedly to select "VCRI ," the
playing source does not change.
Afler pressing
DVD or DVD MUEI'I,
you can perform
the
following
operations
on a DVD player:
I,,,-PLAY
_ID.t
• STOP
II PAUSE
:Start playing.
:Return
to the beginning
of the current
(or
previous)
chapter.
:Skip to the beginning
of the next chapter.
:Stop playing.
:Pause playing.
'Ib resume
press I_ PLAY.
After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.
Note:
For detailed menu operations,
refer
to the instructions
supplied with the
discs or the DVD playe_
G-
TV
You can always perform the following operations:
TV ©/I
:Turn on or off the TV.
TV VOL +/-
:Adjust the volume.
TV/VIDEO
:Set the input mode (either TV or VIDEO).
Afler pressing TV/DBS, you can perform the following operations
on a TV:
CH +/-
1 -9,0,100+
RETURN
:Change
the channels.
:Select the channels.
:Alternate
between
the previously
selected
channel
and the current
channel.
53
Advertisement
Table of Contents
