Table of Contents
Advertisement
On the front panel:
To increase the wflume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
To use neither
sets of the speakers,
press SPEAKERS
ON/OFF
1
and SPEAKERS
ON/OFF
2 so that the SPEAKERS
1 and
SPEAKERS
2 indicators
disappear
from
the display.
The HEADPHONE
indicator
lights up and "HEADPHONE"
appears on the display.
• Activating
the speakers
turns on the Surround
and DSP modes
previously
selected.
I_
i_I • F_, it,h'_'_L'_
From the remote control:
To increase the wflume, press VOLUME +.
To decrease the volume, press VOLUME -.
VOLUME
CAUTION:
Always set the volume to the minimum before starting any sources. If
the volume is set at its high level, the sudden blast of sound energy
can permanently
damage your hearing and/or ruin your speakers.
Notes:
• Thevolumelevelcanbeadjustedwithintherangeof"O"(minimum)
to "70" (maximum).
• If you set One Touch Operation to "ON" (see page 26), you do not
have to adjust the volume level each time you change the source, It
is automatically
set to the stored level
You can listen with the headphones
without
deactivating
both pairs
of speakers
by connecting
a pair of headphones
to the PHONES
.jack
on the front panel. If you want to use a pair of headphones
without
outputting
sounds
from the front speakers,
you must turn off both
pairs of the front speakers
as mentioned
above.
HEADPHONE
mode
When using the headphones,
the folk)wing
signals
are output
regaMless
of your speaker
setting:
For 2 channel
software,
the front left and right channel
signals
are output directly
h-ore the headphones.
For multi-channel
software,
the front
left and right, center, and
surround
channel
signals
are down-mixed
and then output
from the headphones.
• If a DSP mode is activated, you can enjoy the DSP effects.
"3D H.PHONE" appears on the display and the DSP indicalor
lights up on the display. (See page 34.)
IMPORTANT:
You can activate two pairs of the front speakers at the same time only
when the SPEAKER
LOAD SELECTOR
switch on the rear panel is
set to the "HIGH" position and when signals are sent only to front
speakers. Otherwise, activating one pair of the speakers deactivates
the other.
Note:
In the following cases, the speakers connected
to the FRONT
SPEAKERS
_2 terminals are deactivated even ff both pairs of the front
speakers are activated.
- If you select "DVD MULTI" as the source.
- Ifyou select any of the Surround/DSP
modes which activates the
center and/or surround speaker(s).
On the
front
panel
ONLY:
When you have connected
two pairs of the front speakers,
you can
select which to use.
To use the speakers
connected
to the
FRONT
SPEAKERS
(1) terminals,
press
SPEAKERS
ON/OFF
1 so that the
SPEAKERS
1 indicalor
lights up on the
display.
Make sure that the SPEAKERS
2
indicalor
is not lit on the display.
SPEAKERS ON/OFF
To use the speakers
connected
to the FRONT
SPEAKERS
@
terminals,
press SPEAKERS
ON/OFF
2 so that SPEAKERS
2
indicator
lights up on the display.
Make sure that the SPEAKERS
I
indicalor
is not lit on the display.
To use both sets of the speakers,
press SPEAKERS
ON/OFF
I and
SPEAKERS
ON/OFF
2 so that the SPEAKERS
I and SPEAKERS
2
indicators
light up on the display.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones,
as its high volume can
damage both the headphones
and your hearing.
• Before turning on speakers again, as its high volume may output
from the speakers.
18
Advertisement
Table of Contents
