Table of Contents
Advertisement
•
USB
Connection
This receiver
is equipped
with a USB terminal
on the front panel.
You can connect
your PC to this terminal
and enjoy
sound
reproduced
through
your PC.
When you connect
your PC for the first time, follow the procedure
below.
• Remember
you cannot
send any signal or data to your PC from
this receiver.
IMPORTANT
• Check if your PC equipped with the CD-ROM drive is running on
Windows"
98", Windows _ Me* or Windows _ XP* and prepare its
CD-ROM.
• Check your PC's BIOS setting--whether
USB is available, and
whether USB IRQ is set to "AUTO" or to available
[RQ number.
How
to install
the USB
drivers
The following
procedure
is described
using the English
version
of
Windows
_ 98. If your PC is running
on a different
version
of
operation
system
or language,
the screens
shown on your PC's
monitor
will differ from the ones used in the following
procedure.
1.
Turn
on your PC and start
running
Windows
9g,
Windows
_ Me or Windows
:_ XP.
If the PC has been turned on, quit all the applications
now running.
2.
Turn on the receiver,
and press USB AUDIO
on tile front
panel or USB on the remote
control.
The lamp on the USB AUDIO
on the front panel button lights
up.
3.
Connect
the receiver
to the PC using
a USB cable (not
supplied).
Your PC automatically
recognizes
this connection,
and shows
the following
screen on the monitor.
usB AUDIO
VIDEO
SV_O
WDEO
t_,:UDm_R
m
USB cable
PC
4.
Install
the USB drivers
tbllowing
the instructions
shown
on
the PC's monitor.
5.
Check if the drivers
are correctly
installed.
I. Open the Control
Panel on your PC: Select IStart] "*
[Sellings]
--+ [Control Panel].
2. Select
[Syslem],
then [Device
Manager]
and click [Sound,
video and game controllers]
and [Universal
serial bus
controllersl.
'Ihe following
window
appears,
and you can check
whether
the drivers
are installed.
Note:
The items shown on the PC's monitor differ depending on
your PC settings.
6.
Change
the PC audio
setting.
I. If you have closed
Control
Panel, open it again: Select
[Start]
-" ISellings]
-" [Control
Panell.
2. Click [Multimedia],
then select "USB
Audio Device
[1 ]" for
"Playback"
of "Audio,"
and close the window.
To play back a CD fi'om CD-ROM
drive on PC, click IMultimedia],
[CD Music[,
then check [Enable digital CD audio for this CD-ROM
device].
Now PC is ready tbr playback
through
the USB connection.
After installation
is completed,
you can use your PC as the playback
source. The PC automatically
recognizes
the receiver
whenever
a
USB cable is connected
between
the PC and the receiver
while the
receiver
is turned on.
• When not using the PC as the playback
source,
disconnect
the
USB cable.
To play back sounds
on the PC, refer to the manuals
supplied
with
the sound reproduction
application
installed
in the PC.
Notes:
• DO NOT turn off the receiver or disconnect the USB cable while
installing the drivers and for several seconds while your PC is
recognizing the receive_
• Use a full speed USB cable (revision 1.0). Recommended
cord
length is 1,5 m.
• If your PC does not recognize the receiver, disconnect
the USB
cable and connect it again. If it does not work yet, restart Windows.
• The installed drivers can be recognized only when the USB cable is
connected between the receiver and your PC.
• The sound may not be played back correctly--interrupted
or
degraded--due
to your PC settings and PC specifications.
• When you do not use the jacks on the frontpanel,
attach the
supplied front terminal cover to protect them from dust.
* Microsoft _, Windows
98, Windows _ Me and Windows _ XP are
registered trademarks of Microsoft corporation.
14
Advertisement
Table of Contents
