Table of Contents
Advertisement
From the remote control ONLY:
Press MUTING to mute the sound through
MUTING
all speakers and headphones
connected.
(_Q@N
"MUTING"
appears
on the display
and the volume
"C/
turns off (the volume
level indicator
goes off).
]
_[_
[]
I% I 1 I"%
/
L..' % ' L..'
/
i'd i i "F T i..i i':"
_E_I
I'll.=l
I
.L I 1 I..I
Ex.: When
the source
is "DVD."
The volume
level
indicator
goes off.
To restore
the sound,
press MUTING
again.
• Turning
MASTER
VOLUME
on the front panel or pressing
VOLUME
+/- on the remote
control
also restores
the sound.
You can dim the display.
From the remote
control
ONLY."
Press DIMMER.
• Each time you press the button, the display dims
and brightens alternately.
DIMMER
Using the Sleep Timer, you can fall asleep
while
listening
to music.
From the remote control ONLY:
Press
SLEEP
repeatedly.
The SLEEP
indica/or
lights up on the display,
and
the shut-off
time changes
in I0 minutes
intervals:
_[_
[],_
,,,_
L,.' U L;
,-'l
I'-'r-'r_
.I ¢':1..
25
.....
:' !... !::. [:. r- .L i:.:.1 !1! i
!'! .........
Ex.: When the source is "DVD."
When
the shut-off
time comes:
The receiver
turns off automa/ically.
To check or change the time remaining
until the shut-off time:
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP
repeatedly
until "SLEEP
0min"
appears
on the display.
('lhe SLEEP
indica/or
goes off.)
• 'I uming off the power also cancels
the Sleep Timer.
Recording
a source
For analog-to-analog
recording
You can record any analog source through the receiver t_
• the cassette deck (or MD recorder) connected to the TAPE/MD
jacks,
• the VCRs connected to the VCR 1 and VCR 2,jacks, and
• the CD recorder connected to the CDR,jacks
_t
the same time.
For digital-to-digital
recording
You can record the
currently
selected digital input source
through the receiver to a digital recording device connected to
the DIGITAL OUT terminal.
Notes:
• Analog-to-digital
and digital-to-analog
recordings are not
possible.
• The output volume level, Midnight Mode (see page 24), Bass
Boost (see page 31), digital equalization
(see page 39),
Surround modes and DSP modes (see pages 32 to 36) cannot
affect the recording.
• The test tone signal (see pages 40 and 41) does not come out
through the DIGITAL OUT terminal
Basic adjustment
auto
memory
This receiver
memorizes
sound settings
for each source
• when you turn off the power,
• when you change
the soume,
and
• when you assign
the source
name (see page 19).
When you change
the source,
the memorized
sellings
for the
newly seleoed
source are automatically
recalled.
The following
can be stored for each source:
• Analog/digital
input mode (see page
19)
• Input attenuator
mode (see page 30)
• Analog
Direct
(see page 30)
• Speaker
channel
output levels (see pages 40 and 41)
• Digital
equalization
pattern
(see page 39)
• Sound paramelers
(see page 42)
• Surround
and DSP mode
selection
(see pages 35 and 36)
• Bass Boost setting (see page 31)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• If you want to memorize the volume level with the above
settings, set "ONE TOUCH (OPR)" to "ON" (see page 26),
20
Advertisement
Table of Contents
