Table of Contents
Advertisement
Changing
the source
name
When you have conneOed all MD recorder to the TAPE/MD jacks
or a DBS tuner to the TV SOUND/DBS ,jacks on the rear panel,
change the source name which will be shown on the display.
On the front panel ONLY:
When changing the source name J_om "TAPE" to "MD':
1.
Press
TAPE/MD
(SOURCE
NAME).
"_"°
• Make sure "TAPE"
appears on the display.
2.
Press
and
hold
SOURCE
NAME
(TAPE/MD)
until
"ASSGN.
MD"
appears
un the display.
_[]
[]
.......m
.......
i
i
h ,I I-.
When changing the source nameJ_om "TV" to "DBS":
1. Press TV SOUND/DBS (SOURCE
NAME).
•
Make sure "TV" appearson the
display.
2. Press and hold SOURCE NAME (TV
SOUND/DBS) until "ASSGN. DBS"
appears on the display.
_EB
[]
..........
25
......
• • ." .:"•? • -
L.:E .:
To change
the source
name
to "TAPE"
or "TV,"
repeal the same
procedure
above.tess
and hold SOURCE
NAME
(TAPE/MD)
Io
select "TAPE,"
or press and hold SOURCE
NAME
(TV SOUND/
DBS) to select "TV?'
Note:
Without changing the source name, you can still use the connected
components, However, there may be some inconvenience,
- "TAPE" or "TV" will appear on the display when you select the MD
recorder or DBS tune_
-
You cannot use the digital input (see page !9) for the MD recorde_
-
You cannot use the COMPU LINK remote control system (see page
43) to operate the MD recorder
Selecting
different
sources
for picture
and
sound
You can watch picture
from a video component
while listening
to
sound from another
component.
Press une uf the audio source selecting buttons--- PHONO,
CD, CDR, TAPE/MD, USB (AUDIO), FM/AM--while
viewing the picture from a video component such as the
VCR ur DVD player, etc.
The
lamp on
the front
panel
button for the selected
source
lights
up.
From the remote control:
£Z£:, i£22;, 0
0
I, _ _i_
_!i _l!it_i!
CDR
PHONO
ZZJ
i
_, C)
C)
Note:
Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source,
Speaker
and signal
indicators
on the display
By checking the following indicators, you can easily confirm which
speakers you are activating and which signals are coming into this
receiver from the source.
Speaker
indicators
(white)
DDD
[s0.w..]
[]
rn[]rql
Surround
back speaker
indicators
*
Signal indicators (red)
:)
: :i LFE
LS
..... s
.................
sa ................
The speaker
indicators
light up--:
• When the corresponding
speakers
are set to "LARGE"
or
"SMALL"
(see "1)Setting
the Speakers"
on page 22) and are also
required
for the Surround/DSP
mode currently
seleded.
*It' you have selected
"1SPK"
for the surround
back speaker quantity
(see page 22), the center smTound
back speaker
indicator
lights up.
It' you have selected
"2SPK,"
the left and right smTound back
speaker
indicators
light up.
• When "SUBWOOFER"
is set to "YES,"
_
lights up. (See
"11 Setting
the Speakers"
on page 22.)
The signal
indicators
light up to indicate
the incoming
signals.
L
: • When digital input is selected:
Lights up when the left
channel
signal comes
in.
• When analog
input
is selected:
Always
lights up.
R
: • When digital input
is selected:
Lights up when the right
channel
signal comes
in.
• When analog
input
is selected:
Always
lights up.
C
: Lights
up when the center channel
signal comes in.
LFE
: Lights
up when the LFE channel
signal comes
in.
LS
: Lights
up when the left surround
channel
signal comes
in.
RS
: Lights
up when the right surround
channel
signal comes
in.
S
: When the monaural
rear channel
signal or 2 channel
Dolby
Surround
encoded
signal comes in.
SB
: Lights
up when the surround
back channel
signal comes
in.
Note:
When "DVD MULT!" is selected as the source, "c," "C," "R," "LFE," "LS"
and "ITS" light up,
On the
front
paneh
[]
17
Advertisement
Table of Contents
