Storing A Program; Editing And Deleting Programs - Sharp AR-FX12 Operation Manual

STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS

STORING A PROGRAM

You can store a destination fax number, speed dialing, polling, erase, dual page scan, 2in1, card shot, and resolution
and exposure settings in a program. This enables you to call up the program and perform the transmission by means
of a simplified operation. (See "USING A PROGRAM" on page 3-17.)
NOTE
A timer setting (page 3-6) cannot be included in a program.
When storing a program for an F-Code operation, one touch keys for destinations must include sub-addresses.
To store a program key, follow steps 1 through 3 on page 6-2, touch the [PROGRAM] key in step 4, and then follow these steps.
1 Touch the [PROGRAM NAME] key.
PROGRAM
No.1
PROGRAM NAME
SETTINGS ADDRESS
RESOLUTION
screen appears. Enter up to 18 characters for the name.
Refer to chapter 7 of "Operation manual (for general
information and copier operation)" for the procedure for
entering letters.
2 Touch the [SETTINGS] key.
No.1
PROGRAM FOR SHARP
PROGRAM NAME
ADDRESS
SETTINGS
RESOLUTION
SPECIAL MODES
3 Touch the keys for the settings you wish to
store.
ENTER PROGRAM YOU REQUIRE.
AUTO
EXPOSURE
STANDARD
RESOLUTION

EDITING AND DELETING PROGRAMS

To edit or delete a previously stored program, follow steps 1 to 3 on page 6-2, touch the [AMEND/DELETE] key in
the screen of step 4, and then follow these steps.
Touch the [PROGRAM] key.
1
EXIT
1/2
PROGRAM
6-8
The "No." that
automatically appears is
the lowest number from 1 to
8 that has not yet been
programmed. When the
[PROGRAM NAME] key is
touched, the letter-entry
CANCEL OK
FAX
ADDRESS BOOK
MODE SWITCH
ADDRESS REVIEW
SPECIAL MODES
For the detailed procedures for each of the settings, refer to
the explanations of those features on the following pages.
[RESOLUTION](page 1-10) [EXPOSURE](page 1-11)
[SPEED DIAL](page 2-4)
[SPECIAL MODES]
ERASE (page 3-4)
2in1 (page 3-7) CARD SHOT (page 3-8)
POLLING (page 3-13)
NOTE
Up to 500 (maximum of 300 on the AR-M351U/AR-
M451U) destinations can be stored in a program.
However, you cannot directly enter fax numbers with
the numeric keys. A destination must be programmed
in an auto dial key (one-touch key or group key) before
it can be stored in a program.
Touch the [OK] key.
4
Your settings are displayed. Make sure
5
they are correct.
PROGRAM
No.1
REGISTRATION
PROGRAM NAME SHARP PROGRAM
ADDRESS 2 ADDRESSES
SETTINGS
RESOLUTION
FINE
SPECIAL MODES DUAL PAGE SCAN
6 When you are finished, touch the [EXIT] key.
If you wish to store another program, touch
the [NEXT] key.
Touching the [EXIT] key returns you to the screen
of step 4 on page 6-2.
Touching the [NEXT] key returns you to the screen of step 1.
Touch the program you wish to edit or delete.
2
DIRECT ADDRESS / AMEND/DELETE
SELECT ADDRESS TO AMEND/DELETE.
PROGRAM
PROGRAM FOR SHARP EMAIL NEWS GROUP
ABYS FAX FORMAT A
When you touch the program name, the edit/delete
screen for the selected program appears.
Touching the [ADDRESS BOOK] key returns you to
the screen of step 1.
3 To edit the program, follow the same procedure as
for storing the program. To delete the program,
touch the [DELETE] key and then touch the [YES]
key in the confirmation screen that appears.
[ADDRESS BOOK] (page 3-3)
DUAL PAGE SCAN (page 3-5)
NEXT EXIT
EXPOSURE AUTO
EXIT
ADDRESS BOOK