Download
Share
Print this page
Star Trac E-TRx Work Instructions
  1. Manuals
  2. Brands
  3. Star Trac Manuals
  4. Treadmill
  5. E-TRx
  6. Work instructions

Star Trac E-TRx Work Instructions

Hide thumbs Also See for E-TRx:

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Technical Manual
STAR TRAC
14410 Myford Road
Irvine, CA 926060 USA
WORK INSTRUCTIONS,
E-TRx / E-TRxe INSTALLATION
2
620-7920 Rev A

Advertisement

loading

Related Manuals for Star Trac E-TRx

Summary of Contents for Star Trac E-TRx

  • Page 1 STAR TRAC 14410 Myford Road Irvine, CA 926060 USA WORK INSTRUCTIONS, E-TRx / E-TRxe INSTALLATION 620-7920 Rev A...

  • Page 2: Tools Required

    • Copyright 2008. Star Trac by Unisen, Inc. Star Trac Fitness, Star Trac®, and the Star Trac Logo are registered trademarks of Unisen Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written permission from Star Trac.

  • Page 3: Unpacking Instructions

    UNPACKING INSTRUCTIONS Step 1. Step 2. Lay the unit in the area where it is going to be Remove the top cover. assembled and remove the straps. Step 3. Step 4. Remove the side box. Lay all boxes on the floor and verify that all components are included (see next page for details).
  • Page 4 Step 5. Step 6. Verify the following components are included in Verify the following components are included in box one: box two: Left handrail (p/n 020-7179). Top rail with electronic display assembly. • Right handrail (p/n 020-7181). • Front neck assembly. •...
  • Page 5 Step 9. Step 10. Verify the following tools are included in the Verify hardware included in the hardware kit: hardware kit : Item Description Screw 5/16”-18x3.0”, Socket Head Cap Item Description Screw 5/16”-18x1.0”, Socket Head Cap Hex (Allen) key, 1/4” Screw 1/4”-28 3/8”, Button Head Socket Cap Hex (Allen) key, 5/32”...

  • Page 6: Installation Instructions

    INSTALLATION INSTRUCTIONS Step 1. Step 2. Lift the front motor shroud off of the frame as- Remove the neck form shipping box and verify sembly. the cables are properly fed through attached protective tube in the base of the neck. Note: Make sure the shroud is properly stored to prevent damage.
  • Page 7 Step 5. Step 6. Insert neck into place, then align the top holes. Align the front holes and fasten with (2) 5/16-18 Using the 1/4” Hex key, fasten the neck to the x 3.0”, (2) 5/16 washers and (2) lock washers. frame with (2) 5/16-18 x 1.0”...
  • Page 8 Step 10. Step 9. (for E-TRxe model only) Now install the top display rail. Align the rail’s Route the user detect cable behind the eleva- mounting holes with the neck holes. tion motor and plug it into the user detect con- nector on the left side of frame.
  • Page 9 Step 13. Step 14. Install left handrail to the frame as shown using Make sure the gap between the rails is closed (3) 5/16-18 x 1.0” socket head screws and (3) and, using the 5/32” Hex key, fasten the (2) 5/16 washers.
  • Page 10 Step 17. Step 18. Now tighten the 4 display rail fasteners (where Tighten handrail fasteners where handrails are neck is joined with display rail) to a torque joined with treadmill frame. Tighten the screws value of 200 in-lbs (22.5 Nm). to a torque value of 200 in-lbs (22.5 Nm).
  • Page 11 Step 21. Step 22. Secure the front of the motor shroud with (2) Re-install the shroud over motor compartment. #10 Truss head screws. Slide the back end of shroud in place (where shroud meets rails) then align the screw holes on the front of shroud with the holes on the frame.
  • Page 12 Step 26. Step 25. Insert the power cord through the tie wrap loop Install left and right handrail grommets. Slide below motor compartment and connect it to the the grommet down the rail and snap it in place power receptacle. over the bed rails covers.
  • Page 13 LED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS Step 2. Step 1. If the back display covers are attached to display Remove electronic display console from pack- console then remove and save them for later aging materials. use, otherwise proceed to the next step. Note: If you are installing an iPod®...
  • Page 14 Step 5. Step 6. Connect the E-Stop cable (g) to J25 connector Connect the Hot Bar cable (i) to J15 connector on the display board, then connect the rail stop on the display board. cable (f) to J5 connector on the display board. Step 8.
  • Page 15 Screw Locations Step 9. Step 10. Connect the main I/O cable (e) to J1 connector Mount the display assembly to the frame and on the display board. note the screw locations (see figure above). Secure top assembly with (4) M4 screws and (4) flat 5/16 washers.
  • Page 16 Step 14. Step 13. Install the lower display back cover onto dis- Install the top back cover piece (p/n 020-7074) play using (6) M4 screws. Next install upper onto the upper display back cover (p/n 020- display back cover onto display with (8) of the 7069 same screws, tighten all screws.
  • Page 17 Once powered up, all features of the unit function properly. ATTENTION Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to • allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill.
  • Page 18 THIS PAGE INTENTIONALLY LEFT BLANK 620-7920 Rev A...
  • Page 19 EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS Step 1. Step 2. Remove all contents from the packaging and Take out the embedded display console out of verify that you have the following parts: the box and remove all packing material. Verify 1. Embedded display console. no visual damage is present on the assembly.
  • Page 20 Step 9. Step 8. Identify the cables coming from neck and rails: Position the display assembly near the top rail while a helper makes the necessary connec- a. DC power cable f. Rail stop cable tions. b. Fan power cable g.
  • Page 21 Contact heart rate Hot Bar E-Stop Step 12. Step 13. Connect the Hot Bar cable (i) to JP7 connector Connect the E-Stop cable (g) and the Contact on the center console board. Heart Rate cable (c) to respective connectors on the FitCpu board located on the back of embed- ded display.
  • Page 22 I/O Interface Screw Locations User-Detect Step 17. Step 16. Mount the assembly to the frame and note the Connect the I/O interface cable (e) to J1 connec- screw locations (see picture above). Secure tor on the translator board located on the top of top assembly with (4) M4 screws and (4) flat the embedded display.
  • Page 23 Step 20. Step 21. Install the lower display back cover onto display If not done already, position the treadmill where using (6) M4 screws. Next install upper display you plan to use it. If necessary, level the tread- back cover onto display with (8) of the same mill using the two adjustable feet under the tail screws, tighten all screws.
  • Page 24 12. Using a chest strap or wireless heart rate simulator, verify heart rate is recording prop- erly. ATTENTION Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to • allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill.
  • Page 25 THIS PAGE INTENTIONALLY LEFT BLANK 620-7920 Rev A...
  • Page 26 iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS Step 1. Step 2. Remove all contents from the packaging and Remove all contents from the hardware kit and verify that you have the following parts: verify that you have the following parts: 1. (1) iPod® center console assembly. 1.
  • Page 27 Step 5. Step 6. Using a Phillips head screw driver, remove the Remove the headphone jack blank cover. screw that holds in the headphone jack cap at Note: You will no longer need the cover and it can the lower front of the hot bar. Retain the be stored away for any possible future use.
  • Page 28 Step 9. Step 10. Install the new iPod® center console. Connect headphone cable coming from Hot Bar rail to the headphone jack on the center con- sole board. Step 12. Step 11. Plug the center console’s 7-pin interface cable Plug the center console keypad cable into J7 into J11 connector on the display board.
  • Page 29 Step 13 Step 14. Plug the DC power cable from the treadmill Plug the center console’s ground cable into the neck into either one of the DC connectors on ground cable tab on the back display bracket. the center console board. Step 16.
  • Page 30 7. Headphone jack the Hot Bar produces clear audio on both sides of earphone. ATTENTION Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to • allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill.
  • Page 31 THIS PAGE INTENTIONALLY LEFT BLANK 620-7920 Rev A...
  • Page 32 MYE® ENTERTAINMENT CENTER CONSOLE INSTALLATION INSTRUCTIONS Step 2. Step 1. Remove all contents from the hardware kit and Remove all contents from the packaging and verify that you have the following parts: verify that you have the following parts: 1. (1) Male-to-mail headphone cable. 1.
  • Page 33 Step 5. Step 6. Using a Phillips head screw driver, remove the Remove the headphone jack blank cover. screw that holds in the headphone jack cap at Note: You will no longer need the cover, and if de- the lower front of the hot bar. Retain the sired, you can store it away for any possible future screw.
  • Page 34 Step 9. Step 10. Install the new MYE® entertainment console in Connect the headphone cable coming from Hot place. Don’t secure console with screws yet. Bar rail to the headphone connector on the MYE® center console. Step 12. Step 11. Plug the center console’s 7-pin interface cable Plug the center console’s keypad cable into J7 into J11 connector on the display board.
  • Page 35 Step 13. Step 14. Plug the DC power cable from the treadmill neck Plug the center console’s ground cable into the into either one of the DC connectors on the cen- ground cable tab on the back display bracket. ter console board. Step 16.
  • Page 36 8. Headphone jack at the front of display produces clear audio on both sides of earphone. ATTENTION Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to • allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmill.
  • Page 37 THIS PAGE INTENTIONALLY LEFT BLANK 620-7920 Rev A...
  • Page 38 PERSONAL VIEWING SCREEN (PVS) INSTALLATION INSTRUCTIONS Step 1. Step 2. Remove all contents from the packaging and Verify following items included in hardware kit: (1) Silicon wrap verify that you have the following parts: 2. (2) Tie strap 1. 1 PVS assembly with mounting 3.
  • Page 39 From PVS Silicon Wrap From Neck Step 6. Step 5. Plug-in the coax cable coming from your cable Connect the coax cable coming the treadmill service provider onto the coax connector lo- neck to the coax cable coming from the PVS cated at the base of the treadmill’s frame.
  • Page 40 Step 10. Step 9. Using a Phillips head screw driver, remove the Install the new PVS center console in place. screw that holds in the headphone jack cap at Don’t secure console with screws yet. the lower front of the hot bar. Retain the screw.
  • Page 41 Step 13. Step 14. Select the E-TRx headphone mount from the kit Take the E-TR headphone jack assembly from and attach it to the available cut-out at the lower the kit and install it onto the back of the center front of the hot bar, then secure with previously console mount, then secure with (1) M4 screw.
  • Page 42 Step 18. Step 17. Plug the DC power cable from the treadmill neck Plug the center console’s 7-pin interface cable into either one of the DC connectors on the cen- into J11 connector on the display board. ter console board. Step 19.
  • Page 43 Step 21. Step 22. Plug identified PVS connectors into the high- Secure the PVS center console in place using lighted locations on the center console board. the screws you saved earlier. Note: The DC power connectors on the center con- sole board are interchangeable.
  • Page 44 ATTENTION • Star Trac recommends that treadmills be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmills •...
  • Page 45 STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http://www.startrac.com 620-7920 Rev A...

  • Page 47: Manager Mode

    ETTINGS AND ESTING After having used your STAR TRAC E SERIES TREADMILL for many workouts, you may wish to change some of its settings. MANAGER MODE The Manager Mode allows you to query and modify the basic settings of your treadmill. To enter Manager Mode: 1.

  • Page 48: Maintenance Mode

    : Adjust the value of the displayed parameter up and down, respectively, in increments of 1 unit or 0.01 unit, as appropriate for the parameter. These keys do not save the new value - see below. STAR TRAC E SERIES TREADMILL O ’ WNER...
  • Page 49 Time, in seconds, to reach maxmium speed from 0 mph (0 km/hr). TION TIME DECELERA- Time, in seconds, to reach 0 mph (0 km/hr) from maximum speed. TION TIME MODEL E-SERIES Treadmill Model STAR TRAC E SERIES TREADMILL O ’ WNER ANUAL...

  • Page 50: Motor Calibration

    When the test is finished the information window will display one of the 2 messages “Passed Calibration” or “Failed Calibration”. If “Failed Calibration” is displayed run test again, if it continues, call for maintenance. 3. Press the S key to exit the Motor Calibration function. STAR TRAC E SERIES TREADMILL O ’ WNER ANUAL...

  • Page 51: Elevation Calibration

    When desired maximum elevation is obtained, press the key. 8. Press the S key to exit the Elevation Calibration function. STAR TRAC E SERIES TREADMILL O ’ WNER ANUAL...

  • Page 52: Troubleshooting

    HAPTER ROUBLESHOOTING Star Trac recommends that you refer your questions about your STAR TRAC E SERIES TREADMILL operation and suspected mal- functions to Star Trac’s Customer Service Hotline at (800) 503-1221, or USA 1-714-669-1660. However, you may wish to investigate error messages that appear in the Information Window.

This manual is also suitable for:

E-trxe