Beisler 100 Operating Instructions Manual page 52

2.10.6
2.11
2.11.1
2.11.2
3
3.1
3.2
3.3
3.4
3.5
3.6
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
3.6.6
3.6.7
3.6.8
3.7
3.7.1
3.7.2
3.7.3
3.8
3.9
3.10
3.10.1
3.10.2
3.11
3.12
3.12.1
3.12.2
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
5
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
5.4
5.4.1
5.4.2
5.5
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
3-2
Change light mask ............................................................................................... 3-16
Dart stretcher ....................................................................................................... 3-16
Fixing in the guiding plate .................................................................................... 3-16
Magnet switch at the dart stretcher cylinder ........................................................ 3-16
Adjustments at the sewing head ...................................................................... 3-17
Height adjustment ................................................................................................ 3-17
Lateral adjustment ............................................................................................... 3-17
Driving belt tension of the sewing motor .............................................................. 3-17
Top threat cutter (Beisler sewing head) ............................................................... 3-18
Height of top threat catcher ................................................................................. 3-18
Center knife adjustments ..................................................................................... 3-18
Switching on ........................................................................................................ 3-18
Switching off ........................................................................................................ 3-18
Safety initiator at the center knife pole ................................................................. 3-18
Depth adjustment of the safety initiator ............................................................... 3-18
Height of center knife ........................................................................................... 3-19
Shear angle of the center knife ............................................................................ 3-19
Lateral adjustment ............................................................................................... 3-19
Needle protection ................................................................................................. 3-19
Adjustments of the bobbin threat catcher (Beisler sewing head) ......................... 3-20
Catcher adjustment .............................................................................................. 3-20
Time of bobbin threat cutting ............................................................................... 3-20
Duration of bobbin threat cutting .......................................................................... 3-20
Sensitivity of the bobbin detector (option) ............................................................ 3-20
Clean tactual head of the bobbin detector (option) .............................................. 3-21
Adjust piping detection ......................................................................................... 3-21
Lateral adjustment ............................................................................................... 3-21
Adjust intensity ..................................................................................................... 3-21
Swing up sewing head ......................................................................................... 3-22
Upper threat monitor ............................................................................................ 3-22
Switch on time ..................................................................................................... 3-22
Filter threat monitor .............................................................................................. 3-22
Adjustments at the mitre knifes ....................................................................... 3-23
Basic adjustment locked mitre knife (seam end) ................................................. 3-23
Basic adjustment movable mitre knife (seam start) ............................................. 3-23
Mitre knife height ................................................................................................. 3-23
Mitre knife broadth ............................................................................................... 3-23
Pre-stabber .......................................................................................................... 3-24
Lateral adjustment ............................................................................................... 3-24
Fine adjustment in the length ............................................................................... 3-24
Tighten cog-belt of the mitre knife drive ............................................................... 3-24
Adjustment of machine options ....................................................................... 3-25
Automatic push-back blocking ............................................................................. 3-25
Height of the take off roller ................................................................................... 3-25
Mitre knife slant position ...................................................................................... 3-26
Distance between basic bodies ........................................................................... 3-26
Height adjustment ................................................................................................ 3-26
Center adjustment ............................................................................................... 3-26
Adjust mitre knife stops ........................................................................................ 3-26
Knife arrangement ............................................................................................... 3-26
Arrangement of the mitre knife during flap pocket production ............................. 3-27
Split needle (Beisler sewing head) ....................................................................... 3-27
Distance to cylinder of the top threat catcher ...................................................... 3-27
Center adjustment ............................................................................................... 3-27
Vylene adjustments .............................................................................................. 3-27
Correct vylene adjustment ................................................................................... 3-27
Demount vylene plate .......................................................................................... 3-28
Change cutting pressure...................................................................................... 3-28
Adjust vylene supply ............................................................................................ 3-28
Easy-running of the vylene roll ............................................................................ 3-28
Vylene supply speed ............................................................................................ 3-28