Cisco CRS-1 - Carrier Routing System Router Troubleshooting Manual page 54

Validating and Troubleshooting Cisco IOS XR Software Configuration
in commit is empty.
Jul 5 14:48:28.044 cfgmgr/common 0/RP0/CPU0 t6
Jul 5 14:49:11.832 cfgmgr/common 0/RP0/CPU0 t4
Jul 5 14:49:11.832 cfgmgr/common 0/RP0/CPU0 t4
NOT-PROCESSABLE'
Jul 5 14:51:22.738 cfgmgr/common 0/RP0/CPU0 t4
Jul 5 14:51:22.738 cfgmgr/common 0/RP0/CPU0 t4
NOT-PROCESSABLE'
Jul 5 14:51:22.738 cfgmgr/common 0/RP0/CPU0 t4
PROCESSABLE'
Jul 5 14:51:22.738 cfgmgr/common 0/RP0/CPU0 t4
with option '0x1'
Jul 5 14:51:22.793 cfgmgr/common 0/RP0/CPU0 t4
d recovery flag = '0x0'
Jul 5 14:51:26.114 cfgmgr/common 0/RP0/CPU0 t4
tartup config.
Jul 5 14:51:26.128 cfgmgr/common 0/RP0/CPU0 t4
ith option '0x0'
Jul 5 14:51:26.135 cfgmgr/common 0/RP0/CPU0 t4
tatus - '0x0' with error: 'No error'
Jul 5 14:51:26.245 cfgmgr/common 0/RP0/CPU0 t4
rror: 'Invalid argument'
Jul 5 14:51:26.288 cfgmgr/common 0/RP0/CPU0 t4
rror: 'Invalid argument'
Jul 5 14:51:26.296 cfgmgr/common 0/RP0/CPU0 t4
itdb returns error: 'Invalid argument'
!
!
!
The output shows that the configuration files are stored on disk0 and the state of the node is active (State
is 'active'). The administration configuration is applied during startup for the designated shelf controller
(DSC) (Attempting to apply ascii admin startup config from file '/qsm/cfsroot/admin/admin.cfg'.). The
secure domain router (SDR)-specific configuration is applied from the saved binary check points
(Attempting to apply binary LR s tartup config.). Several invalid argument errors were returned when
attempting to restore the startup configuration from the binary checkpoints. If there are invalid argument
errors, contact Cisco Technical Support. For Cisco Technical Support contact information, see the
"Obtaining Documentation and Submitting a Service Request" section on page viii
The output also shows the state of queue as PROCESSABLE or NOT-PROCESSABLE. A
NOT-PROCESSABLE state can indicate that the interface is still in the preconfiguration state. If the
queue is not processable, then interfaces cannot be restored. This queue state information can be looked
at along with the startup config information, as it is one of the gating factors for allowing the queue to
be processable.
In the following example, the a list of historical changes to the configuration is displayed.
RP/0/RP0/CPU0:router# show configuration history commit
Sno.
~~~~
1
2
3
4
5
6
7
8
9
10
11
Cisco IOS XR Troubleshooting Guide for the Cisco CRS-1 Router
1-44
Event Info
~~~~~ ~~~~
commit id 1000000001
commit id 1000000002
commit id 1000000003
commit id 1000000004
commit id 1000000005
commit id 1000000006
commit id 1000000007
commit id 1000000008
commit id 1000000009
commit id 1000000010
commit id 1000000011
Chapter 1
Infra band COMPLETE 0
Suspend flag value 1
State of the request queue is '
Suspend flag value 1
State of the request queue is '
State of the request queue is '
Startup config apply requested
Turboboot flag = '0x0', Passwor
Attempting to apply binary LR s
commitdb_purge_entries called w
commitdb_check_status returns s
commitdb_load_changes returns e
commitdb_create_delta returns e
commitdb_save_running_from_comm
Time Stamp
~~~~~~~~~~
Mon Aug 14 17:09:58 2006
Mon Aug 14 17:41:34 2006
Mon Aug 21 08:05:42 2006
Mon Aug 21 12:39:31 2006
Mon Aug 21 12:43:29 2006
Mon Aug 21 12:45:48 2006
Mon Aug 21 13:23:08 2006
Mon Aug 21 13:24:56 2006
Mon Aug 21 13:26:05 2006
Mon Aug 21 13:55:08 2006
Tue Aug 22 13:52:09 2006
General Troubleshooting
in the Preface.
OL-21483-02