Show Install Active Command - Cisco CRS-1 - Carrier Routing System Router Troubleshooting Manual

Validating and Troubleshooting Cisco IOS XR Software Package Installation
Info:
Info:
Info:
Info:
Install operation 6 completed successfully at 07:30:48 UTC Tue Mar 07 2006.

show install active Command

Use the show install active command to display active software packages. Verify that the command
output matches the output of the show install committed command. If the output does not match, when
you reload the router, the software displayed in the show install committed command output is the
software that will be loaded. For example, the following output shows two different software package
versions, one is the active version and the other is the committed version, so when the router reloads,
The 3.2.6 version will be loaded even though 3.3.0 is the currently active version on 0/RP0/CPU0:
RP/0/RP0/CPU0:router(admin)# show install active location 0/rp0/cpu0
Node 0/RP0/CPU0 [RP] [SDR: Owner]
Boot Image: /disk0/hfr-os-mbi-3.3.0/mbihfr-rp.vm
Active Packages:
RP/0/RP0/CPU0:router(admin)# show install committed location 0/rp0/cpu0
Node 0/RP0/CPU0 [RP] [SDR: Owner]
Boot Image: /disk0/hfr-os-mbi-3.2.6/mbihfr-rp.vm
Committed Packages:
disk0:hfr-mgbl-3.2.6
disk0:hfr-mcast-3.2.6
disk0:hfr-mpls-3.2.6
disk0:hfr-k9sec-3.2.6
disk0:comp-hfr-mini-3.2.6
If the expected active software packages are not displayed, install the packages (if required) and activate
the packages. See Cisco IOS XR Getting Started Guide for the Cisco CRS-1 Router for information on
installing and activating Cisco IOS XR software packages. The following example output shows the
active packages for all cards in a router:
RP/0/RP0/CPU0:router# show install active
Node 0/1/SP [SP] [SDR: Owner]
Node 0/1/CPU0 [LC] [SDR: Owner]
Node 0/6/SP [SP] [SDR: Owner]
Cisco IOS XR Troubleshooting Guide for the Cisco CRS-1 Router
1-32
[SUCCESS] /bootflash/hfr-diags-3.3.0: Verification Successful.
[SUCCESS] /bootflash/hfr-admin-3.3.0: Verification Successful.
[SUCCESS] /bootflash/hfr-base-3.3.0: Verification Successful.
[SUCCESS] /bootflash/hfr-os-mbi-3.3.0: Verification Successful.
disk0:hfr-infra-test-3.3.0
disk0:hfr-mgbl-3.3.0
disk0:hfr-mcast-3.3.0
disk0:hfr-mpls-3.3.0
disk0:hfr-k9sec-3.3.0
disk0:comp-hfr-mini-3.3.0
Boot Image: /disk0/hfr-os-mbi-3.3.0/sp/mbihfr-sp.vm
Active Packages:
disk0:hfr-diags-3.3.0
disk0:comp-hfr-mini-3.3.0
Boot Image: /disk0/hfr-os-mbi-3.3.0/lc/mbihfr-lc.vm
Active Packages:
disk0:hfr-diags-3.3.0
disk0:comp-hfr-mini-3.3.0
Boot Image: /disk0/hfr-os-mbi-3.3.0/sp/mbihfr-sp.vm
Active Packages:
disk0:hfr-diags-3.3.0
Chapter 1 General Troubleshooting
OL-21483-02