Cisco CRS-1 - Carrier Routing System Router Troubleshooting Manual page 26

Verifying the System
Command or Action
Step 14
show system verify start
show system verify report
Example:
RP/0/RP0/CPU0:router# show system verify start
RP/0/RP0/CPU0:router# show system verify report
Step 15
show (ipv4 | ipv6} interface brief
Example:
RP/0/RP0/CPU0:router# show ipv4 interface brief
Examples
The output from the show platform command indicates that all expected nodes are in the run state. If
all nodes in the system are active, the cards should be in the IOS XR RUN and the SPAs should be in the
OK state.
RP/0/RP0/CPU0:router(admin)# show platform
Node
-----------------------------------------------------------------------------
0/1/SP
0/1/CPU0
0/1/0
0/1/5
0/6/SP
0/6/CPU0
0/6/0
0/6/4
0/6/5
0/RP0/CPU0
0/RP1/CPU0
0/SM0/SP
0/SM1/SP
0/SM2/SP
0/SM3/SP
The example output shows that all expected nodes are in the run state.
The output from the show version command indicates the version of software being run on the nodes
and from which location (disk or network). Check that the expected software version and images are
installed.
Cisco IOS XR Troubleshooting Guide for the Cisco CRS-1 Router
1-16
Purpose
A two-step command that produces system reports.
•
•
The output of the show system verify report command
provides a comparison of the system at the time of the show
system verify start snapshot and the show system verify
report snapshot. The output provides a sanity check of the
system provided the show system verify start system
snapshot was taken when the system was healthy or before
an event.
Verify that the system parameters are as expected.
Displays the usability status of interfaces.
Verify that all expected interfaces are listed, that they have
the correct assigned address, and that they are in the
expected states.
Type PLIM
MSC(SP) N/A
MSC Jacket Card
MSC(SPA) 4XOC3-POS
MSC(SPA) 8X1GE
MSC(SP) N/A
MSC Jacket Card
MSC(SPA) 4XOC3-POS
MSC(SPA) 8XOC3/OC12-POS
MSC(SPA) 8X1GE
RP(Active) N/A
RP(Standby) N/A
FC/S(SP) N/A
FC/S(SP) N/A
FC/S(SP) N/A
FC/S(SP) N/A
Chapter 1
show system verify start—Starts the system verify
process (creates the initial baseline file)
show system verify report—Generates a report for the
system verification process (report of the current
status)
State Config State
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
OK PWR,NSHUT,MON
OK PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
OK PWR,NSHUT,MON
OK PWR,NSHUT,MON
OK PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
IOS XR RUN PWR,NSHUT,MON
General Troubleshooting
OL-21483-02