Table of Contents
Advertisement
|
Table 41. Diagnostic error messages (continued)
| | | | |
Message
| |
|
| |
DIAG-CMISA1
|
|
Err#2032
|
|
| | | |
DIAG-CMNOBUF
|
Err#1029
|
|
|
|
|
DIAG-DATA
|
|
|
|
Err#266E
|
|
|
Err#306E
|
|
|
|
|
DIAG-ERRSTAT
|
|
|
|
Err#2640-2647
|
|
|
|
Err#3040-3047
|
Err#3840-3847
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIAG-INIT
|
|
|
|
Err#264F
|
|
|
Err#304F
|
Err#384F
|
| |
| |
DIAG-INTNIL
|
|
Err#2031
|
| |
| |
DIAG-INTNOTCLR
|
|
Err#102C
|
| |
|
|
DIAG-LCMEM
|
|
|
Err#1027
|
|
| |
|
| |
DIAG-LCMEMTX
|
|
Err#1F27
|
|
Err#1028
|
|
|
| |
DIAG-LCMRS
|
|
|
Err#1F25
|
|
Err#1025
|
|
|
| |
DIAG-LCMTO
|
|
|
Err#1F26
|
|
Err#1026
|
| | | |
DIAG-MEMNULL
|
Err#0112
Failing test
Description
cmiTest
An attempt to send a CMI
message from ASIC to ASIC
failed.
centralMemoryTest
The port could not get any buffer.
portLoopbackTest
The payload received by the port
crossPortTest
did not match the payload
transmitted.
portLoopbackTest
The port error statistics counter is
crossPortTest
non-zero, meaning an error was
spinSilk
detected when receiving frames.
One of the following status errors
occurred:
v Enc_in – Encoding error, inside
v CRC_err – Cyclic redundancy
v TruncFrm – Truncated frame
v FrmTooLong – Frame too long
v BadEOF – Bad end of file
v Enc_out – Encoding error,
v BadOrdSet – Bad symbol on
v DiscC3 – Discarded class 3
portLoopbackTest
The port failed to go active in the
crossPortTest
loopback mode requested.
spinSilk
cmiTest
ASIC failed to get a CMI error
(interrupt).
centralMemoryTest
The interrupt bit could not be
cleared.
centralMemoryTest
Data read from the central
cmemRetentionTest
memory location did not match
data previously written into the
same location.
centralMemoryTest
A central memory transmit path
failure: ASIC 1 failed to read ASIC
2 using the transmit path.
centralMemoryTest
A central memory read short: M
cmemRetentionTest
bytes requested but got less than
M bytes.
centralMemoryTest
A central memory timeout: Data
cmemRetentionTest
transfer initiated did not complete
within the timeout period.
ramTest
Test failed to malloc.
frame
check on frame failed
outside frame
fiber-optic cable
frames
Probable cause
Action
ASIC failure
1
ASIC failure
1
System board, GBIC
2
module, or fiber cable
failure
ASIC, system board,
2
GBIC module, or fiber
cable failure
ASIC, system board,
2
GBIC module, or fiber
cable failure
ASIC failure
1
ASIC failure
1
ASIC failure
1
System board failure
1
ASIC failure
1
ASIC failure
1
System board failure
1
Appendix C. Error messages
123
Advertisement
Table of Contents
