Cascade Setup (Cascad) Page - Yamaha DME64N - Pro Audio Owner's Manual

4 Gain
Individually sets the gain of each head amplifier channel.
Edit using the "Numeric Parameters" editing procedure
described on page 36.
NOT E
The gain of the DME24N internal head amplifiers can be
adjusted from +10 dB to –60 dB in 1-dB increments. The
internal circuitry switches at about the –45-dB point, and the
signal is automatically muted at that point to prevent noise.
The AD8HR gain can be adjusted from +10 dB to –62 dB in
1-dB steps, and the AD824 gain can be adjusted from +10 dB to
–62 dB in 6-dB steps.
The PAD will be internally switched on or off when the gain of
the DME24N built-in head amplifier is adjusted between -8 dB
and -7 dB. Keep in mind that noise may be generated if there is a
difference between the Hot and Cold output impedance of the
external device connected to the IN connector when using
phantom power.
5 +48V
Individually turns phantom power ON or OFF for each
head amplifier channel.
Use the [E ] and [F ] keys to position the cursor at the
desired channel, then press the [ENTER] key to alternately
turn phantom power for that channel ON and OFF.
• Always turn the phantom power off when it is not
needed.
CAUTION
• Phantom power should only be used with phantom-
powered condenser microphones. Turning phantom
power ON when other types of equipment are
connected can result in damage. Balanced dynamic
microphones, however, will not be affected by phantom
power.
• To prevent speaker and possible hearing damage, be sure
to turn power amplifiers OFF when turning phantom
power ON or OFF. It is also a good idea to turn the
output level all the way down (page 39).
6 Phantom Master Switch (AD8HR only)
Displays overall phantom power ON or OFF.
7 High-pass Filter (HPF) (AD8HR only)
Individually turns the high-pass filter for each AD8HR
head amplifier channel ON or OFF. This parameter is only
available for the AD8HR head amplifier. Use the [E ] and
[F ] keys to select a channel, then press the [ENTER] key
to turn the HPF for that channel ON or OFF.
8 High-pass Filter Frequency (Frq) (AD8HR
only)
Individually sets the high-pass filter frequency for each
AD8HR head amplifier channel. This parameter is only
available for the AD8HR head amplifier.
Edit using the "Numeric Parameters" editing procedure
described on page 36.

Cascade Setup (CASCAD) Page

Shows the status of the [CASCADE] connectors. Refer to
"CASCADE Connection" on page 31 for connection
details.
Settings are made from the DME Designer application
running on the connected computer.
N OTE
This page only appears on the DME64N.
1
2
3
1 Head Margin
Shows the status of the head margin of the audio signal
handled via the [CASCADE] connectors.
0dB: The head margin is 0 dB.
-18dB: The head margin is -18 dB.
N OTE
The Head Margin setting only applies when connected to a
mixer. When not connected to a mixer the head margin is
automatically set to 0 dB.
2 Unit No
Shows how many devices the unit is from the beginning of
the cascade chain.
OUT
IN
PM5D DME64N
Unit No = 01
3 Mixer I/O
Shows the status of the channels to be used for audio
signals cascaded to a mixer.
■ : Channel audio will be transmitted to and received
from mixer.
: Channel audio will be transferred between DME64N/
24N units.
N OTE
Make sure that the Mixer I/O setting is the same for all cascaded
DME64N/24N units.
DME64N/DME24N Owner's Manual
Utility Displays
OUT IN OUT IN
DME64N DME64N
Unit No = 02 Unit No = 03
55