Yamaha DME4io-C Owner's Manual
Yamaha DME4io-C Owner's Manual

Yamaha DME4io-C Owner's Manual

Digital mixing engine satellite
Hide thumbs Also See for DME4io-C:
Table of Contents

Advertisement

DIGITAL MIXING ENGINE SATELLITE
Owner's Manual
EN

Advertisement

Table of Contents
loading

Summary of Contents for Yamaha DME4io-C

  • Page 1 DIGITAL MIXING ENGINE SATELLITE Owner’s Manual...
  • Page 2 PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT INPUT PEAK PEAK PEAK DME Satellite SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2007 Yamaha Corporation...
  • Page 3: Important Safety Instructions

    Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert CAUTION the user to the presence of uninsulated RISK OF ELECTRIC SHOCK “dangerous voltage” within the product’s DO NOT OPEN enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
  • Page 4 The wire which is coloured BROWN must be connected to the ter- cal waste. minal which is marked with the letter L or coloured RED. (lithium disposal) • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)
  • Page 5 • Never insert or remove an electric plug with wet hands. other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. If you notice any abnormality • Do not place the power cord near heat sources such as heaters or radiators, and •...
  • Page 6: Backup Battery

    The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slipper y surface. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
  • Page 7: Table Of Contents

    Precautions for Using a Rack-mounted DME Satellite ..8 Initializing the DME Satellite........32 Introduction to the DME Satellite ....9 References ........33 Differences between DME8i-C, DME8o-C, and DME4io-C ..............9 Options ................. 33 ICP1.................. 33 DME Satellite Features ........... 9 CP4SW, CP4SF, and CP1SF..........33 Audio System Network ..........
  • Page 8: Foreword

    Thank you for choosing a Yamaha DME8i-C/DME8o-C/DME4io-C Digital Mixing Engine Satellite. In order to take full advantage of the features and performance provided by the DME8i-C/DME8o-C/DME4io-C, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.
  • Page 9: Precautions For Using A Rack-Mounted Dme Satellite

    PEAK DME Satellite SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT DME Satellite INPUT PEAK PEAK PEAK DIGITAL MIXING ENGINE SATELLITE SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 10: Introduction To The Dme Satellite

    Introduction to the DME Satellite Differences between DME8i-C, DME8o-C, and DME4io-C The differences between these three models are as follows: ■ DME8i-C This model features 8-channel analog inputs. ■ DME8o-C This model features 8-channel analog outputs. ■ DME4io-C This model features 4-channel analog inputs and 4-channel analog outputs.
  • Page 11: Audio System Network

    One DME Satellite unit has a number of configurations, and a configuration has a number of preset parameters. User Defined buttons (User Defined parameters) Assigning parameters to be User Defined parameters enables you to control the device from the ICP1. Refer to the DME Designer Owner’s Manual for details. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 12 PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE PEAK PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT INPUT Scene 1 Scene Recall Scene 2 DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 13: Signal Types

    [REMOTE] Connector — — (such as AD8HR head page 29 amplifier) • Transmission/reception of MIDI messages The number of I/O [INPUT]/[OUTPUT] channels depends on — — page 28 Connectors (audio in/out) model. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 14: System Examples

    PEAK DIGITAL MIXING ENGINE SATELLITE SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT CobraNet Analog In Ethernet Switching Hub DME4io-C Analog Out CobraNet Switching Hub Analog In Analog Out DME8o-C DME4io-C Analog Out Analog In DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 15: About Dme Designer

    Refer to the “Connecting to a Computer” (page 22) for more information on connecting a computer to the DME Satellite. Refer to the DME Designer Installation Guide for detailed information on installing the DME Designer application and required software drivers. Refer to the DME Designer Owner’s Manual for setup and operation instructions. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 16: About Cobranet

    Number of bundles per channel and usable channels Bundle Bundle Bundle Bundle Bundle Bundle Bundle Bundle Channels per Bundle 9-16 – – – – – – 1–4 5–8 9–12 13–16 – – – – 1–2 3–4 5–6 7–8 9–10 11–12 13–14 15–16 DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 17: Multicast And Unicast Bundles

    Device A and receiving bundles on Device D, then Device Network A will transmit the unicast bundels to Device D. CobraNet Device CobraNet Device DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 18: Conductors And Performers

    Ethernet cables are categorized into crossover cables and straight cables. When you connect two devices directly together, use a crossover Ethernet cable. Use a switching hub and straight cables to connect three or more network devices. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 19: Controls And Connectors

    3 [MASTER] Indicator Lights green when the device is operating as the group mas- ter. The indicator is turned off if the device is operating as a slave. You can assign the group master in DME Designer. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 20 You can use the “Last Mem. Resume” set- ting in DME Designer to set up the DME Satellite so that at startup it will recall the scene selected before you turned off the power to the device. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 21: Rear Panel

    NO T E 232C/RS-422 compatible controller such as those from AMX or Crestron. See “Remote Connection ([REMOTE] Use a CAT5 STP (Shielded Twisted Pair) cable for this Connector)” on page 29 for connection details. connection to prevent electromagnetic interference. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 22 9 [INPUT] Connectors These Euroblock connectors receive 8-channel analog audio signals on the DME8i-C. These Euroblock connectors receive 4-channel analog audio signals on the DME4io-C. ) [OUTPUT] Connectors These Euroblock connectors output 8-channel analog audio signals on the DME8o-C. These Euroblock connectors output 4-channel analog audio signals on the DME4io-C.
  • Page 23: Connecting To A Computer

    SIGNAL DIGITAL MIXING ENGINE SATELLITE PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL INPUT DME Satellite SCENE SCENE HOME HOME UTILITY UTILITY LEVEL LEVEL MUTE MUTE CANCEL CANCEL ENTER ENTER Computer (Running MIDI USB Cable Sequencer or similar application.) DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 24: Network Settings

    If a particular DME Satellite unit is assigned as slave, you must set its master ID to the value of the 4th octet of the master DME Satellite IP address. NO T E If you are using the DME Satellite along with a DME64N/24N, assign the DME Satellite as the master. This will optimize the network communication speed. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 25: Ethernet Connection ([Network] Connector)

    Since the DME Satellite supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a straight or crossover cable. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 26 Use a CAT5 STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. • If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting.
  • Page 27 DIGITAL MIXING ENGINE SATELLITE PEAK PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT INPUT DME Satellite DME Satellite (IP address: 192.168.0.40) (IP address: 192.168.0.10) (Master ID: 2) (Master ID: 3) Computer (IP address: 192.168.0.1) DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 28: Audio I/O Connection

    CobraNet network. However, some devices, even with an MY card installed, might be unable to transmit or receive control data. For details, refer to the owner’s manual for the device in which you plan to install the interface card. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 29: Analog Audio Connection ([Input] & [Output] Connectors)

    Slotted Screwdriver Terminal Screw Euroblock Plug Insert cables. Securely tighten terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. Insert the Euroblock plug into the Euroblock connector on the rear panel. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 30: Connecting To An External Device

    NO T E Refer to “DME-N Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron).
  • Page 31: Cobranet Connection (Cobranet Connectors)

    • If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D, you must specify a value of 2 as the fourth octet of the group master DME Satellite’s IP address. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 32: Gpi Connection ([Gpi] Connector)

    Euroblock Plug Remote Switch Box Remote Fader Box Remote LED Box Switches LEDs and Resistors 10k ohm Linear Taper Potentiometer NO T E You can use DME Designer to adjust the input calibration parameters for the [GPI] connector. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 33: Other Functions

    When initialization is complete, reset the dip switch to its previous position (page 20), then turn off and on the power to the unit. Be sure to reset the dip switch to the previous position to prevent possible damage to the device. CAUTION DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 34: References

    The controller switches enable you to turn the parameter settings On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the parameter values. CONTROL PANEL CONTROL PANEL CONTROL PANEL CP4SF CP1SF CP4SW DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 35: Troubleshooting

    LEDs do not light up. • Make sure that the [POWER] switch is turned ON (page 19). • If the device still does not turn on, contact a Yamaha dealer. No communication between the DME • Connect the cable properly (page 22, 24).
  • Page 36: Midi Data Format

    MIDI Bank Select MSB/LSB and Program Change Specifies the MIDI receive channel (1 ~ 16). messages are also transmitted by the DME8i-C/DME8o-C/ DME4io-C as specified by the “MIDI Program Change Table” as- 3.4 MIDI Tx Switch signments. Program Change Tx Switch: turns Bank Select MSB, LSB, and Transmission does not occur while configurations are being Program Change transmission on or off.
  • Page 37: Midi Format

    When the “Parameter Change Rx Switch” is On, Parameter the Bank Select MSB/LSB and Program Change number corre- Change messages are received on the MIDI channel specified by the sponding to the lowest number will be transmitted. “Device ID (Rx Ch)” parameter. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 38 Refer to “Supplementary Information 2” for information on setting Change Table” can be set up via DME Designer.) Parameter Data values. Multiple messages can be assigned to a single parameter, but the DME8i-C/DME8o-C/DME4io-C will only transmit one of the as- Status F0h (11110000b) System Exclusive Message signed messages.
  • Page 39: Midi Implementation Chart

    MIDI Implementation Chart YAMAHA [Digital Mixing Engine Satellite] Date :16-FEB-2006 Model DME8i-C, DME8o-C, DME4io-C MIDI Implementation Chart Version : 1.0 Function... Transmitted Recognized Remarks Basic Default 1 - 16 1 - 16 Memorized Channel Changed 1 - 16 1 - 16 Default ˛...
  • Page 40: Display Messages

    Execute the “Initialize DME” operation, then restart it. If the error Flashing indicators are still indicating the error, execute the “Delete All Data” PEAK PEAK PEAK initialization. If the problem persists, contact a Yamaha dealer. SIGNAL SIGNAL SIGNAL PEAK PEAK...
  • Page 41: General Specifications

    –60dBu, GAIN: –60dB +2.0 +4.0 +6.0 INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB +2.0 +4.0 +6.0 <DME8o-C> Input Output CONDITIONS UNITS INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB +2.0 +4.0 +6.0 DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 42 OUTPUT 1–8 600Ω –64 Rs=150Ω, GAIN: +10dB –82 –79 All input & output level controls: 0dB <DME8o-C> Input Output CONDITIONS UNITS Rs=150Ω, GAIN: +10dB INPUT 1–8 OUTPUT 1–8 600Ω –82 –79 All input & output level controls: 0dB DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 43 METERING POINT CONDITIONS UNITS PEAK red LED: ON –3 dBFs INPUT 1–8 SIGNAL green LED: ON –40 dBFs <DME8o-C> METERING POINT CONDITIONS UNITS PEAK red LED: ON –3 dBFs OUTPUT 1–8 SIGNAL green LED: ON –40 dBFs DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 44: Input/Output Characteristics

    *2.All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz). DIGITAL INPUT & OUTPUT CHARACTERISTICS Terminal Format Data length Level Connector CobraNet CobraNet 16/20/24bit 100Base-TX RJ-45x2 *1 *1.PRIMARY,SECONDARY *2.Double Channel format and Single format are supported at 96kHz. DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 45: [Network] Connector (100Base-Tx Ethernet, Rj-45)

    2 –– 6 3 –– 3 3 –– 1 4 –– 4 4 –– 4 5 –– 5 5 –– 5 6 –– 6 6 –– 2 7 –– 7 7 –– 7 8 –– 8 8 –– 8 DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 46: Dimensions

    Unit: mm * Specifications and descriptions in this owner’s manual are for information purpose only. Yamaha Corp. reserves the right to charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
  • Page 47: Index

    [NETWORK] Connector ..........20, 44 Dimensions ................45 [NETWORK] Indicator ............18 Dip Switch ................20 Network Settings ..............23 Display Messages ..............39 DME4io-C ................9 DME8i-C .................. 9 octet ..................23 DME8o-C ................. 9 Options ..................33 [OUTPUT] Connectors ............21 Electrical Characteristics ............40 [ERROR] Indicator ..............
  • Page 48 Straight and Crossover Cable Wiring ........44 System Examples ..............13 Troubleshooting ..............34 unicast bundles ................ 16 USB Connection ..............22 [USB] Connector ..............18 User Defined buttons (User Defined parameters) ....10 Warning Messages ..............39 zones ..................10 DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 49 MEMO DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 50 MEMO DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 51 MEMO DME8i-C/DME8o-C/DME4io-C Owner’s Manual...
  • Page 52 Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo.
  • Page 53 Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2006 Yamaha Corporation WG50630 606IPDHxx.x-xxA0 Printed in Japan This document is printed on chlorine free (ECF) paper with soy ink.

This manual is also suitable for:

Dme8i-cDme8o-c

Table of Contents