1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | RPS183...
• To reduce the risk of electric shock, unplug the power cord before removing the sys- tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. User's Manual | RPS183...
The board and accessories in the package may not come similar to the information listed above. This may differ in accordance with the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales repre- sentative. User's Manual | RPS183...
3. Screw tight two of the spring screws at opposite corners into the mounting holes. And DDR5_1 SODIMM (Top) then proceed with the other two spring screws. DDR5_2 SODIMM (Bottom) 9 10 9 10 Mounting holes User's Manual | RPS183...
Page 29
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. User's Manual | RPS183...
4. Make sure the notch on memory card is aligned to the key on the socket. Retention Notch Notch DDR5_1 SODIMM (Top) DDR5 SO-DIMM DDR5_2 SODIMM (Bottom) 9 10 Retention Clip 9 10 Socket Top View DDR5-1 SODIMM DDR5-2 SODIMM 4 5 ° User's Manual | RPS183...
Page 31
Inspect that the clip sits in the notch. If not, please pull the clips outward, release and remove the card, and mount it again. Step 3 User's Manual | RPS183...
“Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously. User's Manual | RPS183...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | RPS183...
Enables this field for Windows XP and Linux which are optimized for Hyper-Threading technol- ogy. Select disabled for other OSes not optimized for Hyper-Threading technology. When dis- abled, only one thread per enabled core is enabled. Enable / Disable AES (Advanced Encryption Standard) User's Manual | RPS183...
Check to enable render standby support. Enable/Disable processor Turbo Mode (requires EMTTM enabled too). AUTO means enabled. C states Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and nothing is executing. User's Manual | RPS183...
MEBx Setup. This option does not disable manageability features in FW. ME Unconfig on RTC Clear When disabled, ME will not be unconfigured on RTC Clear. Firmware Update Configuration Firmware Update Configuration Configure Management Engine Technology Parameters. User's Manual | RPS183...
Chapter 3 BIOS SETTINGS Advanced Advanced IT8786 Super IO Configuration IT8786 Super IO Configuration ► Serial Port 1, 2 Configuration Serial Port Enable or disable serial port. User's Manual | RPS183...
► Smart FAN Function This section displays the system’s health information, i.e. voltage readings, CPU and system temperatures, and fan speed readings Smart Fan Function Smart Fan Function Setting. Case Open Enable or disable the case open detection function. User's Manual | RPS183...
Fan will start working when the temperature is higher than this limit. Fan full speed temperature limit Fan will be full speed when the temperature is higher than this limit. Fan start PWM Fan will start with this PWM value. User's Manual | RPS183...
Serial Port Console Redirection Serial Port Console Redirection ► Console Redirection Settings Console Redirection By enabling Console Redirection of a COM port, the sub-menu of console redirection settings will become available for configuration as detailed in the following. User's Manual | RPS183...
The system automatically powers on after power failure. • S5 State The system enter soft-off state after power failure. Power-on signal input is required to power up the system. EuP Support Enable or disable EuP function support. User's Manual | RPS183...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or nu- meric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | RPS183...
USB Power Control DFI WDT Configuration Server CA Configuration Watchdog Timer 5_Dual: Support system wake up from S3/S4 by USB KB&MS Enable or disable Watchdog Timer. 5V: No support system wake up from S3/S4 by USB KB&MS User's Manual | RPS183...
Chapter 3 BIOS SETTINGS Advanced X Chipset Tls Auth Configuration Server CA Configuration Please select a submenu and press Enter. The submenus are detailed in the following pages. Press <Enter> to configure Server CA. User's Manual | RPS183...
PCIE TO USB3, LAN1, M.2-E, M.2-B, M.2-M SATA Speed Control the PCI Express Root Port. This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3. Ports Enable or disable the Serial ATA port function. User's Manual | RPS183...
Chapter 3 BIOS SETTINGS Chipset PCH-IO Configuration ► HD Audio Configuration HD Audio Control the detection of the HD Audio device. • Disabled HDA will be unconditionally disabled. • Enabled HDA will be unconditionally enabled. User's Manual | RPS183...
Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. Expert Key Management Enables expert users to modify Secure Boot Policy variables without full authentication. User's Manual | RPS183...
Select this option to save BIOS configuration settings to a USB flash device. • Restore Setting from file This field will appear only when a USB flash device is detected. Select this field to restore set-ting from the USB flash device. User's Manual | RPS183...
MAC address should be burned or not. c. After updating unique MAC Address from manufacturing, NVM will be protected immediately after power cycle. Users cannot update NVM or MAC address. User's Manual | RPS183...
Need help?
Do you have a question about the RPS183 and is the answer not in the manual?
Questions and answers