Page 2
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | RPS310-R680E/Q670E...
Trusted Computing ......................34 NCT6126D Super IO Configuration ................34 NCT6126D Super IO Configuration ► Serial Port 1, 2 Configuration ....35 NCT6126D Super IO Configuration ► Serial Port 3, 4 Configuration ....35 NCT6126D HW Monitor ....................36 User's Manual | RPS310-R680E/Q670E...
Page 4
• To reduce the risk of electric shock, unplug the power cord before removing the sys- tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. User's Manual | RPS310-R680E/Q670E...
Page 5
The board and accessories in the package may not come similar to the information listed above. This may differ in accordance with the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales repre- sentative. User's Manual | RPS310-R680E/Q670E...
4DIMM 3600MHz system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection. User's Manual | RPS310-R680E/Q670E...
+12v Power Case Open M2CN4 power select AT/ATX mode select PCIE1 InnoAGE Header PCIE2 M2CN3 power select M.2 M-Key PCIE3 InnoAGE Power PCIE4 PS/2 and USB Wake up select CPU FAN S/PDIF DIMM1 DIMM2 DIO Power User's Manual | RPS310-R680E/Q670E...
Page 11
Chapter 2 HARDWARE INSTALLATION DIO0~3 power select DIO4~7 power select DIO power select (5V_DIO) SYSTEM FAN1 USB2_11/12 USB2_13 USB3.1 Gen1 COM1 COM2 COM3 COM4 BIOS PS/2 User's Manual | RPS310-R680E/Q670E...
4 mounting holes around the board. 3. Screw tight two of the spring screws at opposite corners into the mounting holes. And then proceed with the other two spring screws. LGA 1700 M.2 M-Key Mounting holes User's Manual | RPS310-R680E/Q670E...
PS/2 and USB Wake up Select (JP25) Battery Battery LGA 1700 LGA 1700 M.2 M-Key M.2 M-Key 1-2 On: Control by BIOS (default) 2-3 On: Wake up disable 1-2 On: 5V_DIO(default) 2-3 On: GND User's Manual | RPS310-R680E/Q670E...
DIMMs. Not all slots need to be populated. Dual Channel (DC) Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides better system performance because it doubles the data transfer rate. User's Manual | RPS310-R680E/Q670E...
4. Make sure the notch on card is aligned to the key on the socket. 5. Make sure the standoff screw is removed from the standoff. M.2 Module M.2 Socket Stand-off M.2 M-Key Notch M.2 M-Key M.2 E-Key User's Manual | RPS310-R680E/Q670E...
Page 28
Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. User's Manual | RPS310-R680E/Q670E...
When “X” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>. User's Manual | RPS310-R680E/Q670E...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | RPS310-R680E/Q670E...
Enables this field for Windows XP and Linux which are optimized for Hyper-Threading technol- ogy. Select disabled for other OSes not optimized for Hyper-Threading technology. When dis- abled, only one thread per enabled core is enabled. Enable / Disable AES (Advanced Encryption Standard) User's Manual | RPS310-R680E/Q670E...
Enable or disable turbo mode of the processor. This field will only be displayed when EIST is enabled. C states Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and nothing is executing. User's Manual | RPS310-R680E/Q670E...
MEBx Setup. This option does not disable manageability features in FW. ME Unconfig on RTC Clear When disabled, ME will not be unconfigured on RTC Clear. Firmware Update Configuration Configure Management Engine Technology Parameters. Note: The sub-menus are detailed in following sections. User's Manual | RPS310-R680E/Q670E...
This field is used to enable or disable BIOS support for the security device such as an TPM 2.0 to achieve hardware-level security via cryptographic keys. Pending operation To clear the existing TPM encryption, select "TPM Clear" and restart the system. This field is not available when "Security Device Support" is disabled. User's Manual | RPS310-R680E/Q670E...
Advanced Advanced NCT6126D Super IO Configuration NCT6126D Super IO Configuration ► Serial Port 1, 2 Configuration ► Serial Port 3, 4 Configuration Serial Port Serial Port Enable or disable serial port. Enable or disable serial port. User's Manual | RPS310-R680E/Q670E...
Fan Speed Count 1 field. • Fan Speed Count 1 to Fan Speed Count 4 Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will operate according to the specified boundary temperatures above-mentioned. User's Manual | RPS310-R680E/Q670E...
Select parity bits: None, Even, Odd, Mark or Space. Stop Bits Select stop bits: 1 bit or 2 bits. Flow Control Select flow control type: None or Hardware RTS/CTS. Flow Control is for RS485 mode and is only supported by Serial Port 1 (COM1). User's Manual | RPS310-R680E/Q670E...
(G3 state). • S0 State The system automatically powers on after power failure. • S5 State The system enter soft-off state after power failure. Power-on signal input is required to power up the system. User's Manual | RPS310-R680E/Q670E...
Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port it is 100 Ms, for a Hub port the delay is taken from Hub descriptor. User's Manual | RPS310-R680E/Q670E...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or nu- meric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | RPS310-R680E/Q670E...
USB Power Control DFI WDT Configuration Server CA Configuration Watchdog Timer 5_Dual: Support system wake up from S3/S4 by USB KB&MS Enable or disable Watchdog Timer. 5V: No support system wake up from S3/S4 by USB KB&MS User's Manual | RPS310-R680E/Q670E...
Chapter 3 BIOS SETTINGS Advanced Tls Auth Configuration Server CA Configuration Press <Enter> to configure Server CA. User's Manual | RPS310-R680E/Q670E...
System Agent (SA) Configuration Please select a submenu and press Enter. The submenus are detailed in the following pages. Graphics Configuration Settings about graphic. VMD setup menu VMD Configuration Settings PCI Express Configuration : VT-d VT-d capability. User's Manual | RPS310-R680E/Q670E...
Select one of the PCI Express channels and press enter to configure the following settings. PCI Express Configuration Settings LAN1, LAN2, LAN3, LAN4, M.2-E, M.2-M2, PCIE2, PCIE4 SATA Configuration Control the PCI Express Root Port. SATA Device Otpions Settings HD Audio Configuration HD Audio Subsystem Configuration Settings User's Manual | RPS310-R680E/Q670E...
This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3. Ports and Hot Plug • Enabled HDA will be unconditionally enabled. Enable or disable the Serial ATA port and its hot plug function. User's Manual | RPS310-R680E/Q670E...
Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. Key Management Enables expert users to modify Secure Boot Policy variables without full authentication. User's Manual | RPS310-R680E/Q670E...
Refer to the Advanced > CSM Configuration submenu for more information. • Restore Setting from file This field will appear only when a USB flash device is detected. Select this field to restore set-ting from the USB flash device. User's Manual | RPS310-R680E/Q670E...
MAC address should be burned or not. c. After updating unique MAC Address from manufacturing, NVM will be protected immediately after power cycle. Users cannot update NVM or MAC address. User's Manual | RPS310-R680E/Q670E...
Combination of RAID 0 (data striping) RAID 10 (not same mirror) and RAID 1 (mirroring) Note: M.2 PCIe SSD cannot be used to set up a RAID set either with an M.2 SATA SSD or a SATA hard drive. User's Manual | RPS310-R680E/Q670E...
Page 51
SATA device and RAID volume information. The user interface, tray icon service and monitor service allow you to monitor the current status of the RAID volume and/or SATA drives. It enables enhanced performance and power management for the storage subsystem. User's Manual | RPS310-R680E/Q670E...