Cisco 2611XM Software Configuration Manual page 95

Chapter 3 Configuring with the Command-Line Interface
• To view the status of ATM interface, use the show interface atm slot/port command. Make sure that
ATM slot/port and line protocol is up, as shown in the following example:
Router# show interface atm1/0
ATM 1/0 is up, line protocol is up
Router# show atm vc
Interface
1/0.3
1/0.2
Router# show controllers atm 1/0
Interface ATM1/0 is up
IDB:
PHY Inst:62588490
Slot:
VCperVP:256
rct_size:65536
vpvc_sel:3
WIC
---------------
FPGA Dev ID (LB)
FPGA Dev ID (UB)
FPGA Revision
WIC Config Reg
WIC Config Reg2
Int 0 Enable Reg
OL-1957-03
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 800 Kbit, DLY 2560 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s):AAL5 AAL2, PVC mode
24 maximum active VCs, 256 VCs per VP, 2 current VCCs
VC idle disconnect time:300 seconds
Last input never, output 00:00:01, output hang never
Last clearing of "show interface" counters 03:16:00
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
2527 packets input, 57116 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
10798 packets output, 892801 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
VCD /
Name VPI
2 9
1 9
Hardware is DSLSAR (with Alcatel ADSL Module)
62586758 Instance:6258E054
Ser0Inst:62573074
1 Unit:
max_vp:
vpivcibit:16
enabled: 0
Register Value
---------- ----------
0x44
0x53
0x99
0x45
0x07
0x03
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
VCI Type Encaps
36 PVC MUX
37 PVC SNAP
reg_dslsar:3C810000
Ser1Inst: 6257CBD8
1 Subunit: 0
256 max_vc: 65536
connTblVCI:8
throttled:0
Notes
'D'
'S'
WIC / VIC select = WIC;
CTRLE addr bit 8 = 1;
OK LED on;
LOOPBACK LED off;
CD LED on;
Gen bus error on bad ADSL access
ADSL normal interrupt enabled
ADSL error interrupt enabled
Configuring 1-Port ADSL WAN Interface Card
Peak Avg/Min Burst
SC Kbps Kbps Cells
UBR 800
UBR 800
wic_regs:3C810080
us_bwidth:800
pkt Size:4496
total vc:2
vpi_bits:8
Sts
UP
UP
3-33