Cisco 2600 series Overview

Cisco 2600 series Overview

Modular access router with lan and wan connections
Hide thumbs Also See for 2600 series:

Advertisement

Overview of Cisco 2600 Series Routers
Cisco 2600 series routers are modular access routers with LAN and WAN connections that can be
configured by means of interchangeable modules and WAN interface cards.
This guide discusses the router models listed in
This chapter includes the following sections:

Hardware Features

Table 1-1
on each model. These router models are similar in functionality, but differ in the number of interfaces
that are supported as well as the system specifications. (See
Table 1-1
Summary of Cisco 2600 Series LAN Interfaces
Ethernet
Model
(10BASE-T)
Cisco 2610
1
Cisco 2610XM —
Cisco 2611
2
Cisco 2611XM —
Cisco 2612
1
Cisco 2613
Cisco 2620
Cisco 2620XM —
Cisco 2621
OL-2171-06
Hardware Features, page 1-1
Reading the Front-Panel LEDs, page 1-3
Reading the Rear-Panel LEDs, page 1-5
Interface Numbering, page 1-9
System Specifications, page 1-11
Regulatory Compliance, page 1-12
lists the router models described in this guide and summarizes the LAN interfaces supported
Token Ring
(RJ-45)
1
1
Table
1-1.
Fast Ethernet
Network
(10/100)
Module Slot
1
1
1
1
2
1
1
1
1
1
1
1
2
1
Cisco 2600 Series Routers Hardware Installation Guide
C H A P T E R
Table
1-6.)
Advanced
WAN Interface
Integration
Card Slots
Module Slots
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
1
1-1

Advertisement

Table of Contents
loading

Summary of Contents for Cisco 2600 series

  • Page 1: Hardware Features

    C H A P T E R Overview of Cisco 2600 Series Routers Cisco 2600 series routers are modular access routers with LAN and WAN connections that can be configured by means of interchangeable modules and WAN interface cards. This guide discusses the router models listed in Table 1-1.
  • Page 2 • Flash memory—Stores the operating system software image. In Cisco 2691 routers, flash memory • is a CompactFlash memory card. In all other Cisco 2600 series routers, flash memory is a single inline memory module (SIMM). • EIA/TIA-232 (RJ-45) console port for local system access by using a console terminal EIA/TIA-232 (RJ-45) auxiliary port for remote system access or dial backup by using a modem •...
  • Page 3: Reading The Front-Panel Leds

    Figure 1-3 Figure 1-4 show the locations of the LEDs on the front panel of Cisco 2600 series routers. Table 1-3 Table 1-3 describe these LEDs.
  • Page 4 Blink (500 ms ON, 500 ms OFF)—In ROMMON, no errors. Blink (500 ms ON, 500 ms OFF, 2 seconds between codes)—In ROMMON, error detected. Blink (less than 500 ms)—In the Cisco IOS software, the blink rate reflects the level of activity. 1. RPS = Redundant Power System Figure 1-4 Cisco 2691—Front-Panel LEDs...
  • Page 5: Reading The Rear-Panel Leds

    Reading the Rear-Panel LEDs Figure 1-4 through Figure 1-10 show the location of the Cisco 2600 series rear-panel LEDs. Table 1-4 Table 1-5 describe these LEDs. Not all router models are shown in these illustrations. The speed and number of Ethernet and Token Ring Note interfaces varies depending on the router model.
  • Page 6 100 Mbp s Link 10/1 00 ETH ERN ET 0/1 10/1 00 ETH ERN ET 0/0 CON SOL E 10/100BASE-T Auxiliary 10/100BASE-T Ethernet 0/0 port (RJ-45) Ethernet 0/1 (RJ-45) (RJ-45) Console port (RJ-45) Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06...
  • Page 7 Ethernet 0/1 Console (RJ-45) port (RJ-45) Table 1-4 Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers—Rear-Panel LEDs Description LINK When on, a link has been established with the hub or switch at the other end of the cable.
  • Page 8: Modules, Interface Cards, And Memory

    (AIMs), and memory is available online and on the documentation CD-ROM. For information on installing network modules, refer to the documents at • http://www.cisco.com/en/US/products/hw/modules/ps2797/prod_installation_guides_list.html. For information on installing WICs and VICs, refer to the documents at • http://www.cisco.com/en/US/products/hw/modules/ps2641/prod_installation_guides_list.html. Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06...
  • Page 9: Interface Numbering

    – Cards Interface Numbering Each interface (port) on a Cisco 2610, Cisco 2620, and Cisco 2650 series router is identified by number as described in the following sections. WAN and LAN Interface Numbering Cisco 2600 series routers contain the following WAN and LAN interface types: •...
  • Page 10 Interfaces in the WICs are numbered from right to left, starting with 0/0 for each interface type, regardless of which physical slot the WICs are installed in. Cisco 2600 Series Routers Hardware Installation Guide 1-10 OL-2171-06...
  • Page 11: System Specifications

    • 1/1/1—Chassis slot 1/Voice module slot 1/Voice interface 1 System Specifications Table 1-6 Cisco 261x, Cisco 262x, and Cisco 265x System Specifications Description Specification Dimensions (H x W x D) 1.69 x 17.5 x 11.8 in. (4.3 x 44.5 x 30 cm), one rack unit height Weight 10.25 lb (4.66 kg)
  • Page 12: Regulatory Compliance

    UL 60950; CAN/CSA C22.2 No. 60950-00; IEC 60950; AS/NZS 3260; TS001 Regulatory Compliance For compliance information, refer to the Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document that accompanied your router. Cisco 2600 Series Routers Hardware Installation Guide...

Table of Contents