1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 2600 Series
  6. Installation manual

Cisco 2600 Series Installation Manual

Cisco rps adapter plate installation
Hide thumbs Also See for 2600 Series:
Table of Contents

Advertisement

Quick Links

See also: Configuration Manual , Installation Manual
Doc. No.
78-5172-01
Installing the Cisco RPS Adapter Plate
in Cisco 2600 Series Routers
Product Number: ACS-2600RPS=
This document describes how to install an adapter plate in Cisco 2600 series routers for use with the
Cisco Redundant Power System (RPS). The Cisco RPS provides power system redundancy to
external devices (such as routers, switches, or hubs). The system includes two fully redundant AC
input power modules and four DC output power modules for connection to external devices. The
Cisco RPS supports quasi-redundant and fully redundant power source configurations. To use the
Cisco RPS with Cisco 2600 series routers, you must remove the existing power supply and replace
it with a Cisco RPS adapter plate.
This document includes the following sections:
•
•
•
•
•
•
•
•

Safety Recommendations

Follow these guidelines to ensure general safety:
•
Keep the chassis area clear and dust-free during and after installation.
•
Put the removed chassis cover in a safe place.
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Copyright © 1998
Cisco Systems, Inc.
All rights reserved.
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco 2600 Series

Summary of Contents for Cisco 2600 Series

  • Page 1: Table Of Contents

    Cisco 2600 Series Routers Product Number: ACS-2600RPS= This document describes how to install an adapter plate in Cisco 2600 series routers for use with the Cisco Redundant Power System (RPS). The Cisco RPS provides power system redundancy to external devices (such as routers, switches, or hubs). The system includes two fully redundant AC input power modules and four DC output power modules for connection to external devices.

  • Page 2: Safety Warnings

    Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. 2 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die...

  • Page 3: Safety With Electricity

    — Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action. Use the Cisco RPS (model PWR600-AC-RPS) only to power the external Caution device. Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Safety with Electricity...

  • Page 4: Preventing Electrostatic Discharge Damage

    1 and 10 megohms (Mohm). Required Tools and Equipment This kit includes the following items: • Cisco RPS adapter plate, shown in Figure 1 • DC power rating label 4 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers...

  • Page 5: Removing The Cover

    DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. Cisco RPS Adapter Plate for Cisco 2600 series Routers Adapter plate Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Removing the Cover...
  • Page 6 POWER ACTIVITY Lift the cover until it is free from the chassis and then set it aside. Step 7 6 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Removing the Cover ACTIVITY Lifting the Cover Cisco 2600...

  • Page 7: Removing The Power Supply

    If cable tie-wraps on the harness interfere with removing the connectors, cut the Locating the Connectors Power connector Fan connector Removing the Mounting Screw Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Removing the Power Supply AC power supply...

  • Page 8: Installing The Redundant Power Supply Adapter Plate

    CONN SEE MANU AL BEFO RE INSTA LLAT LINK ETH ERN ET 0 8 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Removing the Power Supply AC power supply Cisco 2600 Series Rear Panel (Cisco 2610 Shown)
  • Page 9 RPS. Cisco IOS Release 11.2(7)P or later will provide RPS status information to the network. Installing the Redundant Power Supply Adapter Plate Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Front of chassis...

  • Page 10: Replacing The Cover

    Reinstall the chassis on the wall, rack, desktop, or table. Step 5 Reconnect all cables. Step 6 10 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Reconnecting the Connectors Six-pin connector The top section fits into the rear of the bottom section. The bottom section fits into the front of the top section.

  • Page 11: Obtaining Service And Support

    Note If you purchased your product from a reseller, you can access Cisco Connection Online (CCO) as a guest. CCO is Cisco Systems’ primary, real-time support channel. Your reseller offers programs that include direct access to CCO’s services. For service and support for a product purchased directly from Cisco, use CCO.

  • Page 12: Ordering Documentation

    StreamView, SwitchProbe, The Cell, TrafficDirector, TransPath, VirtualStream, VlanDirector, Workgroup Director, Workgroup Stack, and XCI are trademarks; Empowering the Internet Generation and The Network Works. No Excuses. are service marks; and BPX, Catalyst, Cisco, Cisco Systems, the Cisco Systems logo, EtherChannel, FastHub, FastPacket, ForeSight, IPX, LightStream, OptiClass, Phase/IP, StrataCom, and StrataView Plus are registered trademarks of Cisco Systems, Inc.

Table of Contents