Cisco 2650XM Manuals

Table of Contents

• • 3

    Table of Contents

• 8

  Appendix A Troubleshooting

• 8

  Appendix B Using the ROM Monitor

  • 9

    Safety Warnings
  • 14

    Related Documentation
  • 16

    Cisco 90-Day Limited Hardware Warranty Terms
  • 17

    Obtaining Documentation
    • 17

      Cisco.com
    • 17

      Ordering Documentation
  • 17

    Documentation Feedback
  • 18

    Obtaining Technical Assistance
    • 18

      Cisco Technical Support Website
    • 18

      Submitting a Service Request
    • 19

      Definitions of Service Request Severity
  • 19

    Obtaining Additional Publications and Information

• 8

  Preface

  • 8

    Audience
  • 8

    Organization
  • 8

    Conventions

• 21

  Overview of Cisco 2600 Series Routers

  • 21

    Hardware Features
  • 23

    Reading the Front-Panel LEDs
  • 25

    Reading the Rear-Panel LEDs
  • 28

    Modules, Interface Cards, and Memory
  • 29

    Interface Numbering
    • 29

      WAN and LAN Interface Numbering
    • 31

      Voice Interface Numbering
      • 31

        System Specifications
      • 32

        Regulatory Compliance
      • 33

        Preparing to Install the Router
    • 33

      Safety Recommendations
    • 33

      Safety With Electricity

• 34

  Chapter 2 Preparing to Install the Router

  • 34

    Preventing Electrostatic Discharge Damage
  • 35

    General Site Requirements
    • 35

      Power Supply Considerations
    • 35

      Site Environment
    • 36

      Site Configuration
    • 36

      Equipment Racks
  • 36

    Installation Checklist
  • 37

    Creating a Site Log
  • 38

    Inspecting the Router
  • 38

    Tools and Equipment for Installation and Maintenance
  • 39

    Console and Auxiliary Port Considerations
    • 39

      Console Port Connections
    • 40

      Auxiliary Port Connections
  • 40

    Preparing to Connect to a Network
    • 41

      Ethernet Connections
    • 41

      Token Ring Connections
    • 42

      Serial Connections
      • 42

        Configuring Serial Connections
      • 42

        Serial DTE or DCE Devices
      • 43

        Signaling Standards Supported
      • 43

        Distance Limitations
      • 44

        Asynchronous/Synchronous Serial Module Baud Rates
    • 44

      ISDN BRI Connections
    • 45

      56-K/Switched-56-kbps DSU/CSU Connections

• 47

  Installing the Router

  • 48

    Installing Modules, Interface Cards, and Power Supplies
  • 48

    Cisco Interface Cards Installation Guide
  • 49

    Setting Up the Chassis
    • 49

      Setting the Chassis On a Desktop
    • 50

      Mounting the Chassis in a Rack
      • 51

        Attaching the Brackets to Cisco 261X, Cisco 262X, Cisco 26XxXM, and Cisco 265X Series Routers
      • 55

        Attaching the Brackets to a Router of 2-RU Height
      • 56

        Installing the Router in a Rack
    • 57

      Mounting the Chassis On the Wall
      • 57

        Attaching Rubber Feet to the Router
      • 57

        Attaching Wall-Mount Brackets to the Router
      • 58

        Mounting the Router On the Wall
  • 59

    Installing the Chassis Ground Connection
  • 61

    Power Connections
    • 61

      Connecting Routers to AC Power
    • 62

      Connecting Routers to a DC-Input Power Supply
      • 62

        DC Wiring Requirements
    • 64

      Connecting Routers to the Cisco Redundant Power System
  • 64

    Connecting WAN, LAN, and Voice Cables
    • 64

      Ports and Cabling
    • 65

      LAN, WAN, and Voice Connection Procedures
  • 66

    Connecting to a Console Terminal or Modem
    • 66

      Connecting to the Console Port
    • 67

      Connecting to the Auxiliary Port
    • 68

      Identifying a Rollover Cable
  • 69

    Powering Up the Router
    • 69

      Checklist for Power Up
    • 69

      Front Panel Indicators
    • 70

      Power-Up Procedure
  • 71

    Configuring the Router
    • 72

      Initial Configuration Using SDM
    • 72

      Initial Configuration Using the Setup Command Facility
    • 74

      Initial Configuration Using the CLI (Manual Configuration)

• 77

  Appendix

  • 77

    Isolating Problems
    • 78

      Troubleshooting the Power and Cooling Systems
    • 78

      Environmental Reporting Features
    • 79

      Troubleshooting Modules, Cables, and Connections
  • 80

    System Messages
  • 80

    Recovering a Lost Password
  • 80

    Cisco Technical Assistance Center

• 81

  Appendix

• 81

  Using the ROM Monitor

  • 81

    Entering ROM Monitor Mode
  • 82

    ROM Monitor Commands
  • 83

    ROM Monitor Command Syntax Conventions
  • 84

    ROM Monitor Command Descriptions
    • 84

      Router Management Commands
      • 84

        Boot Commands in the ROM Monitor
      • 85

        Informational Commands in the ROM Monitor
      • 86

        Other Useful ROM Monitor Commands
    • 86

      Debugging Commands
    • 87

      Configuration Register Commands
  • 88

    Recovering Cisco IOS Software Images
    • 89

      Copying an Image From the Console Using the Xmodem Command
      • 89

        Description and Options of the Xmodem Command
      • 89

        Console Requirements
      • 89

        Procedure for the Xmodem Command
    • 90

      Copying an Image From a TFTP Server Using the Tftpdnld Command
      • 90

        Restrictions On the Tftpdnld Command
      • 91

        Procedure for the Tftpdnld Command

• 93

  Appendix

• 93

  Configuration Register

  • 93

    Configuration Register Settings
  • 94

    Changing Configuration Register Settings
  • 95

    Configuring the Boot Field
  • 97

    Enabling Booting From Flash Memory
  • 99

    I N D E X