Denon AVR-4311CI Owner's Manual page 12

STEP 1
Preparation
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
When the setup microphone is
connected, the following screen is
displayed.
AUDYSSEY AUTO SETUP
STEP1 Preparation 1 2 3 4 5 6
Connect the speakers and place them according
to the recommendations in the manual,
Set the following items
If necessary.
Amp Assign
Channel Select
Auto Setup Start
Enter Cancel
RETURN
Start Auto Setup
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select "Amp
Assign" and perform step 3 and 7 of "Set up
"Amp Assign"" (vpage 63).
If unused channels are set with "Channel Select",
measuring time can be shortened. Also, set
"Channel Select" to measure two subwoofers.
For setting, perform steps 9 to 14 of "Set up
"Channel Select"" (vpage 64).
5
Use to select "Auto Setup Start"
ui
and then press ENTER .
Remote control operation
buttons
STEP 2
Detection & Measurement
(Main listening position)
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
confi guration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
Select "Measure" and then press
ENTER .
AUDYSSEY AUTO SETUP
STEP2 Detection & Measurement (main) 1 2 3 4 5 6
Please place the microphone at ear
height at main Iistening position.
Measure
Enter Cancel
RETURN
Start measurement. Output large test tone during measuring
q Measure the subwoofer level
• To stop measuring, select "Cancel" and then
ENTER
press .
• When "Subwoofer" is set to "Skip" with
"Channel Select", this measurement is not
taken, and the process proceeds to "w
Measure each speaker".
w Measure each speaker
• Once the measurements in step q are
complete, the measurements in step w start
automatically.
• The measuring channel changes depending
on the setting of "Set up "Amp Assign""
(vpage 63) and "Set up "Channel Select""
(vpage 64).
• Measurement requires several minutes.
Move the cursor
(Up/Down/Left/Right)
7
The detected speakers are displayed.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
STEP2 Speaker Detection Check
Front Yes
Center Yes
Subwoofer 1spkr
Surround Yes
Surround Back 2spkrs
Front Height No
Retry
Next Measurement
Enter Cancel
RETURN
Proceed to STEP 3 after checking speaker connection result
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use to select "Next →
ui
Measurement" and then press
ENTER .
NOTE
If "Caution" is displayed:
Go to "Error messages" (vpage 11), check
any related items, and perform the necessary
procedures.
When performing Audyssey Auto
Setup over again
ENTER
Press ui to select "Retry", and then press
When measuring has stopped
RETURN
Press , to the "Cancel auto setup?" prompt
is displayed.
ENTER
Press o to select "Yes", then press .
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation .
Confi rm the setting
Set up speakers (Audyssey ® Auto Setup)
STEP 3
Measurement
(2nd – 8th listening position)
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
Move the setup microphone to
position 2, use to select
ui
ENTER
"Measure", and then press
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
STEP3 Measurement(2nd-8th)
Please place the microphone at ear
height at 2nd Iistening position.
Measure
Next Calculation
Enter Cancel
RETURN
Start measurement. Output large test tone during measuring
If you want to omit measurements from the next
position onward, select "Next → Calculation".
(Go to STEP4 Calculation
)
10
Repeat step 9, measuring positions 3
to 8.
When measurement of position 8 is
completed, a "Measurements fi nished."
.
message is displayed.
AUDYSSEY AUTO SETUP
STEP3 Measurement(2nd-8th) 1 2 3 4 5 6
Measurements finished.
Retry
Next Calculation
Enter Cancel
RETURN
Proceed to STEP4 (Calculation)
Return to previous menu
.
9