Related Manuals for ETC High End Systems SolaWash 2000
Summary of Contents for ETC High End Systems SolaWash 2000
- Page 1 High End Systems SolaWash 2000 Automated Luminaire User Manual Version 3.0.15 Part Number: H715-MANL-3.0.15 Rev: B Released: 2024-07...
- Page 2 To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. You can find complete High End Systems terms and conditions and warranty information at etcconnect.com/Support/Warranty.aspx.
-
Page 3: Table Of Contents
Table of Contents Introduction Important Safety Information Help from Technical Services Safety Considerations General Operation and Use Guidelines Fixture Overview Install the Fixture Power Electrical Specifications Input and Power Factor Connector Specifications DMX Control DMX Connector Pinout Connect DMX Cables to Fixture Terminate DMX Set the DMX Start Address DMX Channels... - Page 4 Set Menu Test Menu Preset Menu Error Codes Maintenance Clean the Fixture Replace the Fuse Compliance FCC Compliance SolaWash 2000 User Manual...
-
Page 5: Introduction
Introduction This manual provides important information for the safe installation, configuration, and maintenance of your High End Systems SolaWash 2000 fixture. For your safety, read this entire manual prior to installing, operating, or servicing the fixture. ETC recommends that you update your fixture with the latest version of software before you use the fixture. -
Page 6: Help From Technical Services
Help from Technical Services If you have questions that are not answered by this document, try the ETC support website at support.etcconnect.com or the High End Systems product website at etcconnect.com/Products/Automated-Fixtures. If none of these resources are sufficient, contact ETC Technical Services directly at one of the offices identified below. Emergency service is available from all offices outside of normal business hours. -
Page 7: Safety Considerations
• This fixture is intended for professional use only. Not for residential use. Read the entire manual before using this equipment. • Contact your authorized ETC dealer or Technical Services before performing any service in order to maintain warranty coverage. - Page 8 Note: The light source in this luminaire is not user-replaceable, and must be replaced only by a qualified technician. Contact ETC Customer Support for assistance. Symbols used on the product label are defined below: The luminaire must be installed at least 1.5 m (4 ft Le luminaire doit être installé...
-
Page 9: General Operation And Use Guidelines
• Please use the original packaging if the fixture is to be transported. ETC will not be responsible for the fixture if packaging other than manufacturer provided packaging is used. -
Page 10: Fixture Overview
Fixture Overview For technical specifications of the SolaWash 2000 fixture, see the technical datasheet: etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/SolaWash/2000/Documentation.aspx 1. Lens 2. Tilt lock 3. Pan lock 4. Microphone 5. Display 6. Navigation controls 7. Enclosure handle 8. 5-pin DMX In and Out 9. 3-pin DMX In and Out 10. -
Page 11: Install The Fixture
Install the Fixture Overhead rigging must be performed by qualified personnel. Follow all local and national codes and recommended practices. WARNING: • NEMA Type 1 enclosure, indoor use, dry locations only. Do not use outdoors. This fixture is intended for use where humidity does not exceed 90% (non-condensing). - Page 12 You can install the fixture in any of the orientations shown below. SolaWash 2000 User Manual...
- Page 13 1. Assemble the clamp (provided by others) to the bracket that was provided with the fixture and secure together using appropriately sized hardware (not provided). 2. Align the assembled bracket and quick-lock fasteners into the respective holes on the bottom of the fixture upper enclosure. 3.
-
Page 14: Power
Power WARNING: Connect the fixture to a non-dimmable power source in order to avoid damage to the fixture's internal power supply and other electrical components. Using a dimmable power source can damage the fixture and will void the warranty. Electrical Specifications •... -
Page 15: Dmx Control
DMX Control The SolaWash 2000 fixture operates on standard DMX-512 control bus, controlled by a DMX console. The fixture requires 36 channels of DMX-512. Attach the fixture to the control bus using a two-core, shielded cable with a 5-pin or a 3-pin XLR cable connector (Belden 9729 is preferred). -
Page 16: Terminate Dmx
1, you could set the second fixture to 37 (36+1), the third to 73 (36+37), and so on. DMX Channels The current DMX channel map for the SolaWash 2000 can be found on the ETC website: etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/SolaWash/2000/Documentation.aspx. SolaWash 2000 User Manual... -
Page 17: Configure The Fixture
Configure the Fixture You can configure SolaWash 2000 fixtures through the onboard user interface. Navigate the User Interface 1. Press and hold the [MODE/ESC] button until the display flashes. (The display is powered by battery when the fixture has no power.) 2. -
Page 18: Set Fixture Parameters
View the DMX value of each of the fixture's channels (parameters of the fixture). Scroll to the parameter that you want to view (Pan, Tilt, etc.) and view the value. The DMX value that you view is the DMX value that displays on the main window of the UI until you select a different DMX value to view. - Page 19 View Fixture Head Temperature Navigate: Main Menu → Info → Head Temp Displays the current fixture temperature as read from the fixture head (near the CMY filter). View Fan Speeds Navigate: Main Menu → Info → Fan Speed Displays the speeds of the fixture's fans (in RPM). View Software Version Navigate: Main Menu →...
-
Page 20: Set Menu
Set Menu Set the Status Options Navigate: Main Menu → Set → Status Parameter Value Description No DMX Mode • Close Control mode when DMX is absent. The default value is Hold. • Hold • Auto • Music Pan Reverse • ON Reverse the pan movement of the fixture. - Page 21 Access Service Settings Navigate: Main Menu → Set → Service PIN Parameter Value Description Service PIN Service PIN XXX You must enter the Service PIN in order to access the other Service Setting parameters. The default Service PIN is 050. RDM UID Manufacturer ID This password-protected menu item lets you modify and fixture serial...
-
Page 22: Test Menu
Test Menu Reset (Home) the Mechanical Positions on the Fixture Navigate: Main Menu → Test → Home Reset ("home") all features on the fixture, including, pan, tilt, colors, gobos, etc. Test an Individual Channel Navigate: Main Menu → Test → Test Channel Run a self-test program on individual channels. -
Page 23: Error Codes
Error Codes When you apply power to the fixture, it runs a calibration (homing) sequence and displays any errors that it detects. Example: When the display shows "Error channel: Pan Coarse", it means there is an error in channel 1. When multiple errors are present they will cycle on the display twice, and then the fixture will reset (restart). -
Page 24: Maintenance
• Moving parts must not show any signs of wear and must move smoothly without issue. • The power supply cables must not show any damage, material fatigue, or sediment. • If spare parts are required, order only genuine parts from ETC or your authorized ETC dealer. -
Page 25: Replace The Fuse
Replace the Fuse WARNING: Replace fuses with the specified type and rating only. AVERTISSEMENT : Remplacez les fusibles uniquement par le type et le calibre indiqués. A replaceable AC line fuse is provided in the fixture to prevent overload. Supplies needed: •... -
Page 26: Compliance
Compliance For current and complete compliance information, view the product datasheet: etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/SolaWash/2000/Documentation.aspx For complete product documentation, including compliance documentation, visit etcconnect.com/products. FCC Compliance SolaWash 2000 (For any FCC matters): Electronic Theatre Controls, Inc. 3031 Pleasant View Road Middleton, WI 53562 +1 (608) 831-4116 etcconnect.com This device complies with Part 15 of the FCC Rules. - Page 27 Compliance...
- Page 28 New York, NY | Orlando, FL | Los Angeles, CA | Austin, TX | © 2024 Electronic Theatre Controls, Inc. etcconnect.com | Support support.etcconnect.com | Contact etcconnect.com/contactETC Trademark and patent info: etcconnect.com/ip | Third-party license agreement info: etcconnect.com/licenses Product information and specifications subject to change. ETC intends this document to be provided in its entirety. H715-MANL-3.0.15 Rev B Released 2024-07...
Need help?
Do you have a question about the High End Systems SolaWash 2000 and is the answer not in the manual?
Questions and answers