Table of Contents
Advertisement
installer's information
General Safety Information
1. The appliance installation must conform with
local codes, or in the absence of local codes,
with the current Canadian or National Gas Codes,
CSA B149.1 or ANSI Z223.1 Installation Codes.
2. See general installation and assembly
instructions. The appliance and vent should be
enclosed.
3. This appliance must be connected to the
specified vent and termination cap, outside of
the building envelope. Never vent to another
room or the inside of a building. Make sure that
the vent is fitted as per venting instructions.
4. Inspect the venting system annually for
blockages and any signs of deterioration.
5. Venting terminals must not be recessed into a
wall or siding.
6. Any safety glass removed for servicing must
be replaced prior to operating the appliance.
7. To prevent injury, do not allow anyone who is
unfamiliar with its operation to use the fireplace.
8. Wear gloves and safety glasses for protection
during appliance maintenance.
9. Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
10. Under no circumstances should this appliance
be modified. Parts removed for servicing should
be replaced prior to operating this appliance.
11. Installation, annual inspection, and repairs to
this appliance should be done by a qualified
service person. Have all of your gas appliances
checked annually.
12. Do not slam shut or strike the glass door.
13. Never use solid fuels (wood, paper, cardboard,
coal, etc.) in this appliance.
14. The appliance area must be kept clear of
combustible materials, gases, and other
flammable vapours and liquids.
22
| City Series CST50E
Installation Checklist
IMPORTANT: It will need to be determined if this
appliance will be installed as a Non power vent
or power vent. The venting parameters and size
of the venting differ so it is important to know
which version will be installed.
1. Choose a location for your appliance. Refer to
the following sections:
a) Locating Your Fireplace
b) Clearances
c) Combustible Mantel Clearances
d) Framing & Finishing
e) Venting. See the "Venting Introduction" to
"Venting Arrangements" sections.
2. Assemble standoffs. Refer to the "Unit Assembly
Prior to Installation" section.
Must be done before installing unit into
fireplace.
3. Install vent. See installation procedures sections.
4. Wire 120 volt AC power to the receptacle box
located on the lower right of the appliance.
The Duplex receptacle and cover are included
in the manual package.
On the power vent model, ensure that the
power vent cap is wired to the appliance. See
the manual for details.
Power vent model: This heater requires a 120
volt A.C. supply for operation of the appliance.
Non-power vent model: While the burner
does not require a 120 volt A.C. power supply,
it is recommended as a primary power source.
Batteries (4 AA) should be used as a secondary
power source.
5. Install the junction box supplied with the
appliance. Install the battery box inside the
junction box and hook it to the wire marked
"receiver".
6. On the non-power vent model only:
• Batteries (4 AA) should not be installed into
the battery holder/switch box if electrical
connections are made to the receptacle.
• Install batteries during power outages to
run the main burner.
On the power vent model only:
• Install 3 AA batteries into the transmitter.
• No other batteries are required.
7. See the instructions in this manual on how to
operate the remote control.
8. Make the gas connections and test the pilot.
The configuration must be as per the diagram in
the "Gas Line Installation" & "Pilot Adjustment"
sections.
9. Install standard and optional features. Refer to
the following sections where applicable:
a. Barrier (Outer) Safety Glass
b. Firebox (inner) glass
c. Log Set
d. Fireglass
e. Ceramic stones or other approved media
f. Painted, enamel, or glass panels (panels
required)
10. Plug the three-prong plug into the receptacle.
The three-prong plug is located near the gas
valve on the appliance.
11. Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained.
This includes:
1. Clocking the appliance to ensure the correct
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2. If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
Any alteration to the product
that causes sooting or carboning
resulting in damage is not the
responsibility of the manufacturer.
Advertisement
Table of Contents
