Specifications - SMC Networks LE2FS Series Operation Manual

１.４

Specifications

Battery-less absolute encoder type (Step motor 24 VDC)
Model
Storke [mm] Note.1)
Work load [kg] Note.2)
Pushing force[N] Note.3),4),5)
Speed[mm/s] Stroke Range
Max acceleration/deceleration
2
speed[mm/s ]
Pushing speed [mm/s] Note.6）
Positioning repeatability [mm]
Lost motion [mm] Note.7)
Lead [mm]
Impact/Vibration resistance
2
[m/s ] Note.8)
Actuation type
Guide type
Operating temperature [℃]
Operating humidity [%RH]
Motor size
Motor type
Encoder
Powre supply voltage [V]
Power [W] Note.9),11)
Type Note.10)
Holding force [N]
Power [W] Note.11)
Powre supply voltage [V]
Note.１）Non-standard strokes are available as special orders, so please contact SMC .
Note.２）Maximum payload at acceleration/deceleration of 3000mm/s2.
Work load varies depending on the velocity and acceleration. Please refer to the catalog for the "speed - payload graph".
Furthermore, if the cable length exceeds 5 m, then it will decrease by up to 10% for each 5 m.
Note.３）Pushing force accuracyis ±20% (F.S.).
Note.４）The setting range for the "Pushing force" is from 25% to 45%(LE2FS16) and 25% to 50%(LE2FS25) and 30% to 70%(LE2FS32)
and 30% to 70%(LE2FS40).
The pushing force setting range varies depending on the duty ratio and pushing speed. Please refer to the cataiog for the "Thrust
Conversion Graph"
Note.５）Speed and thrust may vary depending on cable length, load, installation conditions, etc. If the cable length exceeds 5m, the
speed/thrust will decrease by up to 10% for every 5m. (For 15m: Max. 20% reduction)
Note.６）When transporting and pushing a workpiece, operate the actuator with the "Horizontal load capacity" or less.
Note.７）Areference value for correcting an error in reciprocal operation.
Note.８）Impact resistance: In a drop impact test, no malfunction occurred in the axial direction and perpendicular direction of the feed screw.
(value at the initial stage)
Vibration resistance: 45 to 2000 Hz 1 sweep, no malfunction in the axial direction and perpendicular direction of the feed screw.
(value at the initial stage)
Note.９）Indicates the maximum power when operating the actuator only.
Note.１０）Only applies to actuators supplied with a lock.
Note.１１）For the actuator with lock, please add the power consumption for the lock.
LE2FS16
50 to 500
Horizontal 10 15
Vertcal 3 6
23 to 41 44 to 80
to 400 10 to 800 5 to 400
401 to 450 10 to 700 5 to 360
451 to 500 10 to 600 5 to 300
501 to 600 - -
601 to 700 - -
701 to 800 - -
Horizontal
Vertcal
1 to 50
±0.015
±0.02
10 5
Ball screw（LE2FS□） 、Ball screw and belt（LE2FS□R/L）
□28
Max. 58
29 59
4
- 25 -
LE2FS25
50 to 800
18 15 26
12 2 6
86 to 154 41 to 81 67 to 135
3 to 195 20 to 1200 12 to 850
3 to 170 20 to 1100 12 to 750
3 to 140 20 to 1100 12 to 750
- 20 to 900 12 to 540
- 20 to 630 12 to 420
- 20 to 550 12 to 330
10000
5000
±0.02
0.１or less
2.5 20 12
50/20
Linear Guide
5 to 40
90 or less（No condensation）
Battery-less Absolute(Step motor 24VDC)
Battery-less Absolute
24VDC±10%
Max. 72
Non-magnetizing lock
118 47 78
24VDC±10%
40 40
12.5 15
132 to 265 255 to 511
6 to 450 3 to 225
6 to 400 3 to 225
6 to 400 3 to 225
6 to 270 3 to 135
6 to 230 3 to 115
6 to 180 3 to 90
1 to 35
±0.015
6 3
□42
157 294
8