Panel Mounting; Features; Technical Specifications - DSC TL280LEX(R) Manual

The communicator can be used as either a backup or primary communicator. The communicator supports Internet Protocol
(IP) transmission of panel and communicator events over Ethernet/Internet and/or HSPA/GPRS.
The cellular performance of the LE2080(R), TL280LE(R), 3G2080(R) E or TL2803G(R) E communicators depend greatly
on the LTE(4G)/HSPA(3G) network coverage in the local area. A communicator placement test must be performed prior to
mounting the unit . A minimum of one green LED must be ON for good signal strength. Optional 3G/2G and LTE/3G
antenna extension kits are available to improve signal strength if required. GS-15ANTQ, GS- 25ANTQ and GS- 50ANTQ
kits are available for 3G/2G products and LTE- 15ANT, LTE-25ANT, LTE-50ANT extension kits are available for LTE/3G
products.
NOTE: Prior to installation, confirm with the local service provider that the network is available and active in the area where
the communicator will be installed, and that radio signal strength (CSQ) is adequate.
The following communicators are compatible with HS2016, HS2016-4, HS2032, HS2064, and HS2128 panels:
3G2080(R)E
(HSPA(3G)/GPRS only)
l
TL2803G(R)E
(Ethernet/Internet + HSPA(3G)/GPRS dual-path)
l
TL280(R)E
(Ethernet/Internet only)
l
LE2080(R) (LTE(4G)/HSPA(3G) only)
l
TL280LE(R) (Ethernet/Internet + LTE(4G)/HSPA(3G))
l
TL280LE-EU (Ethernet/Internet + LTE(4G)/HSPA(3G)/2G)
l
LE2080-EU (LTE(4G)/HSPA(3G)/2G only)
l
TL280LE-AU(Ethernet/Internet + LTE(4G)/HSPA(3G)
l
LE2080-AULTE(4G)/HSPA(3G)
l
TL280LE-LAT(Ethernet/Internet + LTE(4G)/HSPA(3G)/2G)
l
LE2080-LATLTE(4G)/HSPA(3G)/2G
l
TL280LEX(R) LTE(4G)
l
LE2080X(R)LTE(4G)
l
128-bit AES encryption via cellular and Ethernet/Internet
l
- NIST validation cert number 2645 (for models TL2803G(R)E/3G2080(R)E/TL280(R)E
- NIST validation cert number 4475 (for models TL280LE(R)/LE2080(R))
Backup or primary cellular alarm communication.
l
Automatically converts to 2G (EDGE/GPRS) if HSPA(3G) service is not available (2G not supported on European models
l
only).
Automatically switches from LTE to HSPA(3G) service if LTE service is not available.
l
Ethernet LAN/WAN 10/100 BASE-T (TL2803G(R)E, TL280(R)E, TL280LE(R) only).
l
Fully redundant Ethernet/Internet and cellular dual-path alarm communication (TL2803G(R)E, TL280LE(R) only).
l
Full event reporting to the central station.
l
Individual Internet and/or cellular periodic test transmission.
l
Integrated call routing.
l
Visual Verification (Requires Sur-Gard System 5 Receiver)
l
Remote firmware upgrade capability of the communicator and panel firmware via Ethernet and/or cellular.
l
Panel remote uploading/downloading support via cellular and Ethernet/Internet.
l
PC-LINK connection.
l
Programmable labels.
l
SIA and Contact ID (CID) formats supported.
l
Signal strength and trouble display LEDs.
l
Supervision heartbeats sent via cellular and Ethernet/Internet.
l
Third-party integration over cellular/IP. The product supports third-party application via serial (R-models only), cellular
l
and Ethernet. Refer to third-party application documentation for more information.
NOTE: RS-232 connection is for supplementary use only and was not evaluated by UL/ULC.
The TL2803G(R)E/TL280LE(R) are also suitable to be used with a compatible control unit listed for dual line security trans-
mission when used in conjunction with a DACT or a Public Switched Data Network (PSDN) transmitter, where the PSDN
provides the line security and is the primary line. In this mode, alarm signals are to be sent simultaneously over both com-
munication methods.

Panel Mounting

Features

Technical Specifications

9