Scosche FCJ2076 Installation Kit page 22

1996-98 Jeep Grand Cherokee
RADIO REMOVAL:
1. Extract fve screws from along top of dash instrument bezel.
2. Carefully pop out wood grain trim panel around A/C heater control.
3. Carefully pop out wood
grain trim panel around
headlight switch.
4. Extract four screws from
along bottom of dash
instrument bezel, lift up
and away to remove.
5. Extract two 3/8'' hex heard bolts holding radio, unplug connectors and remove.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1993-95 Jeep Grand Cherokee
1992 Jeep Grand Wagoneer
RADIO REMOVAL:
1. Extract two screws from above the radio securing the radio trim bezel.
2. Extract two screws from above the diagnostics
display panel securing the radio trim bezel.
3. Carefully remove the ashtray and extract two
screws located in the ashtray cavity securing
the radio trim bezel.
4. Pull the radio trim bezel away from the dash,
unplug all connectors and remove the bezel.
5. Extract two nuts securing the radio to the dash, and pull the radio
from the cavity; unplug all connectors and remove the radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1997-02 Jeep Wrangler
RADIO REMOVAL:
1. Extract two screws
from dash bezel.
2. Pry on bezel to release
spring clips and remove.
3. Extract two screws
holding radio, unplug
and remove.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1984-95 Jeep Wrangler
RADIO REMOVAL:
1. Remove three screws from the
lower edge of the dash trim.
2. Extract three screws from the upper
edge of the dash trim.
3. Remove the dash trim.
4. If the vehicle is not equipped with a factory radio,
remove two screws securing the pocket and remove
the pocket. If the vehicle is equipped with a factory radio,
remove two screws from the radio mounting bracket.
5. Pull the radio out of the cavity, disconnect all electrical connections, then remove the radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THIS BRACKET
Usar este braquete
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
USE THESE
SUPPORT TABS
AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THIS BRACKET
Usar este braquete
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
#2190 PANEL
#2190 PANEL
#2190 PANEL
USE THESE BRACKETS
Read pages 2-4
for kit assembly.
22
Read pages 2-4
for kit assembly.
Read pages 2-4
for kit assembly.
USE THIS BRACKET (BOTTOM)
Usar este braquete (Inferior)
Read pages 2-4
for kit assembly.
Usar estos braquetes
#1550 PANEL
REMOVE
ALIGNMENT
PIN -
BOTTOM
Sacar la
clavija de
alineamiento
- Inferior
USE THIS
BRACKET
(TOP)
Usar este
braquete
(Superior)
REMOVE
ALIGNMENT
PIN -
BOTTOM
Sacar la
clavija de
alineamiento
- Inferior