Scosche FCJ2076 Installation Kit page 11

1995-00 Chrysler Sebring
1995-00 Dodge Avenger
RADIO REMOVAL:
1. Carefully pry out on radio/AC control
trim bezel to release the snap clips.
Remove the bezel.
2. Extract the two screws holding radio in,
unplug connector, unbolt ground wire
from rear of radio and remove radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1996-00 Chrysler Town & Country
1996-00 Dodge Caravan
1996-00 Plymouth Voyager
RADIO REMOVAL:
1. Extract two screws in the trim bezel from just above the radio.
2. Pop off small trim below radio and extract (2) screws from behind.
3. Pull the radio trim bezel away from the dash, unplug the ac/heating control.
4. Extract the two screws securing the radio to the dash, pull the radio from the cavity, disconnect
the ground strap, unplug all connectors and remove the radio.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas pestañas
como sea necesario
"L" SPACER Espaciador "L"
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1994-95 Chrysler Town & Country
1994-95 Dodge Caravan
1994-95 Plymouth Voyager
RADIO REMOVAL:
1. Using a panel removal tool carefully pry up on the dash panel at the base of the windshield
(speaker grille panel) to release the fastening clips securing it to the dash and pull out on the
panel to remove.
2. Pry up the piece of trim that looks like a vent in front of the instrument light cluster on top of the
dash using a panel removal tool to release and remove the trim.
3. Carefully pry out on the trim panel surrounding the heater controls using a panel removal tool to
release the fastening clips securing the trim to the dash and remove the trim.
4. Extract the three screws securing the bottom of the radio trim bezel to the dash.
5. Extract the three screws securing the front of the instrument light cluster to the top of the dash.
6. Extract the screw securing the back of the instrument light cluster to the dash, pry up on the
light cluster with a panel removal tool, unplug all connectors and remove.
7. Extract the three screws securing the top of the radio trim bezel to the dash on the drivers side
of the dash.
8. Pull the radio trim bezel away from the dash, unplug all connectors, shift the gear select lever
into low, tilt the steering wheel down and remove the bezel.
9. Extract the two screws securing the radio to the dash, pull the radio from the cavity, disconnect
the ground strap unplug all connectors and remove the radio.
USE THESE SUPPORT
TABS AS REQUIRED
Usar tantas de estas
pestañas como sea
necesario
USE THIS BRACKET
Usar este braquete
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
USE THIS BRACKET
Usar este braquete
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
Read pages 2-4
for kit assembly.
#2190 PANEL
#2190 PANEL
USE THIS BRACKET (BOTTOM)
Usar este braquete (Inferior)
#2190 PANEL
11
USE THIS BRACKET (BOTTOM)
Usar este braquete (Inferior)
"R" SPACER
Espaciador "R"
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
REMOVE ALIGNMENT
PIN - BOTTOM
Sacar la clavija de
alineamiento - Inferior
USE THIS
BRACKET (TOP)
Usar este
braquete
(Superior)
Read pages 2-4
for kit assembly.
Read pages 2-4
for kit assembly.