Advertisement
Available languages
Available languages
1986-89 Ford Taurus
RADIO REMOVAL:
1. Remove two screws from the bottom of the radio trim panel.
2. Carefully pry on the edges of the trim panel to release the plastic
clips and pull the panel away from the dash.
3. Disconnect the power wire for the
antenna switch and remove the
radio trim panel.
4. Remove four screws from the
radio mounting brackets, slidethe
radio out from the dash, disconnect
all electrical, and remove the radio.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1985-86 Ford Mustang
1985-86 Mercury Capri
RADIO REMOVAL:
1. Open the armrest glove box and remove four screws in the bottom of the glove box.
2. Remove two screws at the forward edge securing the hand brake trim. Remove the trim.
NOTE: There may be two additional screws below this trim on some cars.
3. Unsnap the gear lever trim from the front, slide it forward, and remove it.
4. Open the ashtray and remove one screw from each side.
Pull the ashtray/lighter trim up and disconnect the wires.
5. Remove four screws from below the ashtray and pull the
console up. Disconnect the wiring harness and remove
the console.
6. Remove two screws above the radio face and one screw
from below the radio. Pull out the radio and disconnect
the wires, then slide the radio towards the front
of the car and out the back of the cavity.
SECURE THE BRACKETS TO THE BOSSES LOCATED ON THE BACK SIDE
OF THE KIT WITH THE SUPPLIED HARDWARE. SEE PAGE 3.
Asegurar los braquetes en sus ranuras en la parte posterior del juego
usando los tornillos autoenroscantes provistos. Ver la página 3.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
1984-87 Ford Tempo
RADIO REMOVAL:
1. Remove two screws securing the trim panel below the steering
column. Carefully unsnap the trim panel and remove it.
2. Remove three screws along the upper edge of the dash panel: two
screws below the radio, and one screw from the dash pocket.
3. Using a thin blade screwdriver, carefully push up two
retaining clips, one on each side of the
steering column, and slide the dash panel up and off.
4. Remove four screws retaining the radio bracket assembly
and remove the radio. Disconnect the power, antenna,
and speaker wires.
NOTE: INSTALLATION OF A DIN UNIT MAY REQUIRE
DASH MODIFICATIONS.
NOTA: La instalación de una unidad DIN puede requerir
modifcar el tablero del vehículo.
SECURE THE BRACKETS TO THE BOSSES LOCATED ON THE BACK
SIDE OF THE KIT WITH THE SUPPLIED HARDWARE. SEE PAGE 3.
Asegurar los braquetes en sus ranuras en la parte posterior del juego
usando los tornillos autoenroscantes provistos. Ver la página 3.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS
Usar las pestañas sombreadas y los braquetes indicados. Cortar las pestañas restantes y descartarlas.
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
1984-87 Mercury Topaz
AND DISCARD. FOR DIN ISO INSTALLATION, SEE PAGE 4.
Para la instalación de radios DIN ISO ver la página 4.
USE THIS BRACKET
Usar este
braquete
#1550 PANEL
20
Read pages 2-4
for kit assembly.
USE THIS BRACKET
Usar este braquete
Read pages 2-4
for kit assembly.
Read pages 2-4
for kit assembly.
Advertisement
